Hi!
I run 200.8 on the 7850 ICPMS for drinking water.
I calibrate with 10, 50, 100, 250, and 500 ppb for Cu (among others). I would like to calibrate up to 2,000 or higher for Cu - but every time I try to calibrate above 500, my CCV and LFB fail…
Hello I have an ICP-MS 7900. My Check Performace fails all the time. I washed the entire system and replaced the chambers and cone again. The same applies to oil changes. Nevertheless, my Check Performace fails. Can anyone help me with this? Or someone…
Hello
We have an agilent ultivo qqq and last week when trying to run a checktune it failed giving a message saying calibrant bottle is empty or nebulizer is clogged. Nevertheless the calibrant bottle is definitely not empty, and the nebulizer also doesnt…
Hello, I have a G1321B that showed errors during the OQPV. The FSE changed the flash lamp Iand the Intensity test is OK arround 10000 counts buen the and Raman ASTM Signal/Noise fail. I want to know if there are another test to do.
I changed my acquisition method from using front FID to back FID. I changed this in the acquisition method detector, signals, and columns sections. On my status tab, the detector is still showing front FID and the online signals is showing no options…
Hello,
Our lab currently uses a headspace-GC-FID to analyze for ethanol in blood samples. We have a multi-level, internal standard calibration curve as well as control samples at various concentrations that are analyzed in a sequence. Is there a way…
The Digest of upcoming webinars has been updated as of January 4.
Notable additions include:
Spectroscopy Digital Workshop & Bootcamp (16)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from contaminants…
Hello lperry ,
The document below explains what that error is, essentially it could be that an ALS is not ready for injection, or some other piece of hardware connected to the GC.
6890 GC Not Ready Messages (agilent.com) (bottom of page 9).
…
Hello,
I am expeirencing the same issue after having to reload E.02.02.1431. The quant report prints as one job and the chromatogram and the spectra reports (I'm printing a detailed report) print as a second job.
I've done as ron_tackett mentioned…
When doing autotune I get high precursor in mass 502. I get 12.79% and the limit is 12%. The manual says that it could be contaminated. The equipment has had preventive maintenance recently but it has now this problem. Previously it had a ratio of mass…
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...