Hello,
I am not sure exactly what you are doing but to use part of the text in an if you can parse apart the text using string functions or use the like comparison. So your =IF(COUNTIF( A2 ,"*mg*"),"Value if true","Value if false") would be =If(A2…
How many total runs on this system?
8890 and Intuvo: Service Mode, Instrument, Usage
7890: Service Mode , Diagnostics, Instrument Status
6890: Options, Diagnostics, Instrument Status
A 6890/5975 probably has many, many runs on it and passed…
There could be issues with either control signals to the HED power supply or the power supplied to the HED power supply. These electronic issues are down in the depths of the instrument and should be handled by a trained service engineer. Please contact…
A bit late maybe, but you can set the printer within the macro using the MYPRINTER = "name of printer". Use the command before your STARTPRINT command, and then at the end of the macro remove it (REMOVE MYPRINTER), so that it will only be active for the…
Here's a link to the video from this event!
(+) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion - Forum - Gas Chromatography - Agilent Community
You should always consider that after re-igniting the lamp, it typically requires 60-90 minutes establishing a stable detector signal.
Based on this it does not always make sense and saves lifetime shutting off the lamp.
Keep constant flow 1.2 ml/min into the MS and do a Pulsed Splitless injection, tips in the help section of the Operating manual. Your system's diffusion high vacuum pump can only handle 2.0 ml/min maximum so do not exceed that ever.
If you have a 30m…
In Manual Tune, PFTBA closed, set the scan range to 10-100, then click on the spectrum scan button. The spectrum will show repeatedly in the middle window to the left at the long red arrow..
Beautiful. Does the spacing change with a different column flow rate? If this is 1.2 ml/min, for example, is it different with only 1.0 ml/min? If it changes and you did the inlet and column maintenance properly, the issue is before those. If it does…
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...