Hi all,
I am currently troubleshooting a leaky 1260 infinity II HPLC-SFC-ELSD and want to carry out a leak test in the utility program, but i could not find a clear, detailed description on how to do this. Could anyone direct me to the correct resource…
Hi!
I still need help yes, please!
- On the machines (GC system and Injector) it just says HP6890 (see photos attached)
- The PC we employ is an old Windows XP running one, that was used to run the GC-FID before we want to control it with the serial…
Hi there, I noticed recently that the ECD back signal on Agilent GC 7890 (using it for trace gas analysis) is oddly spiking (while the FID is a straight, consistent line). It never used to do this. I just recently changed the inlet septum, could this…
Hi, I would suggest to test the same without column installed to the FID. If problem looks similar check for leaks at the FID gas lines and clean the FID. If not clean the inlet and replace the split vent line and filter. Maybe try a new column.
BR…
Hi Community
I have an Issue on one of our GC-FIDs 6890N. I have large Peak Tailing, especially on the back of my chromatogramm:
What i already did:
- New Column
- New Septa/liner
- New Gold Plate
- Cleaned Inlet and Detector
- Re…
I have a Cary 3500 and running Cary UV Workstation Software 1.2 and Windows 10
I downloaded the new Cary UV Workstation Software 1.3 via the Agilent SubscribeNet.
first I ran the systemPreparationTool.exe
That finished without issues.
Then I ran…
Any special procedures to prepare for cross-country shipment a 7890B with SS, PP inlets, heated valve oven, and TCD-FID? Also a 7697A with 100-vial tray?
*The system and method are given at the bottom of this post*
I am working with an Agilent 8860 operating a DB-624 UI (30m x 0.25mm x 1.4um) column with nitrogen carrier gas and split inlet (20:1). The system was shut down for approximately 1 year, and…
Turning off the systems on Friday night that need to be ready to go on Monday morning is not recommended. It can take quite some time for a GC/MS to come back up to operational after being shut down. Even cooling the temperatures all down and then heating…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...