Hi,
this is a very nasty mass axis.
Could you please confirm, that you have S-Lenses installed, as they are configured.
Please have a look, through this troubleshooting guide and follow the instructions. Hopefully it will solve your problems, or…
ICP-MS MassHunter Version 4.1. I cannot Startup Standard Lens Tune!
The message appears "Failed to add Startup/Hardware tasks to Queue; Enter path for batch folder".
As usual (my Batchs)- everything works.
Hello,
Our Headspace sampler 7697A Leak test failed. Leak test failing at the stage 1 off the Restriction and Pressure Decay Test.
Going from there, the sample probe was replaced as well as the pressurization solenoid valve but without success.
…
Hello vtpolywood ,
What type of GC do you have, if I may? If it's an 8890 for example there are some Diagnostic tests built-in that you can run on the Cool On Column inlet. Have you recently changed gas tanks (whether carrier, FID fuel, air or makeup…
In MSD Chemstation, you can specify which signal to use for quantification: TIC, Target Ion, or GC Signal (for GC detectors like FID, TCD, etc.) Go to the Calibrate menu and select Edit
Compounds. On the Compound Table Identification tab, look for the…
Hi,
I plan to attempt some SimDist analysis in accordance with D2887 on my agilent GC-FID. I was hoping that I could achieve this without additional software (i.e. just through manual manipulation of the data acquired by Chemstation), but apparently…
Our micro GC 990 is Natural Gas Analyzer B and B extended version with 3 channels (PoraPLOT U, 6-meter CP Sil 5 CB, CP-Molsieve 5A). We are having trouble with data processing. We have 2 calibration gases from Agilent (Natural Gas mixture and Universal…
Hi everyone.
We have a 8890 Agilent GC with nickel catalyst and FID detector. We would like to use hydrogen as carrier gas, but we don’t know the right flow rates, because the manual is indicating flow rates only for using helium as carrier gas.
For…
the abundance of ion 69. I rechecked the source and it doesn't look dirty. then I did an autotune it stopped on the width mass axis of the second quadrupole.
Finally, after 2 or 3 more attempts, I ended up completing the autotune with an abundance of…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...