Hello,
I am not sure exactly what you are doing but to use part of the text in an if you can parse apart the text using string functions or use the like comparison. So your =IF(COUNTIF( A2 ,"*mg*"),"Value if true","Value if false") would be =If(A2…
How many total runs on this system?
8890 and Intuvo: Service Mode, Instrument, Usage
7890: Service Mode , Diagnostics, Instrument Status
6890: Options, Diagnostics, Instrument Status
A 6890/5975 probably has many, many runs on it and passed…
There could be issues with either control signals to the HED power supply or the power supplied to the HED power supply. These electronic issues are down in the depths of the instrument and should be handled by a trained service engineer. Please contact…
A bit late maybe, but you can set the printer within the macro using the MYPRINTER = "name of printer". Use the command before your STARTPRINT command, and then at the end of the macro remove it (REMOVE MYPRINTER), so that it will only be active for the…
Here's a link to the video from this event!
(+) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion - Forum - Gas Chromatography - Agilent Community
You should always consider that after re-igniting the lamp, it typically requires 60-90 minutes establishing a stable detector signal.
Based on this it does not always make sense and saves lifetime shutting off the lamp.
Keep constant flow 1.2 ml/min into the MS and do a Pulsed Splitless injection, tips in the help section of the Operating manual. Your system's diffusion high vacuum pump can only handle 2.0 ml/min maximum so do not exceed that ever.
If you have a 30m…
In Manual Tune, PFTBA closed, set the scan range to 10-100, then click on the spectrum scan button. The spectrum will show repeatedly in the middle window to the left at the long red arrow..
Beautiful. Does the spacing change with a different column flow rate? If this is 1.2 ml/min, for example, is it different with only 1.0 ml/min? If it changes and you did the inlet and column maintenance properly, the issue is before those. If it does…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...