Hi Marty,
I am Yew Mun colleague.
Thanks for your help. we run samples in sequence. The ChemStation version we have is 2.141.0.0 . I will try to setup the report in method and let you know how it goes.
Hema
Hi
I have one problem with my 5977B.
The tune no finish, the principal problem or error is "Tune action stopped: Gain and offset = 0 and peaks are too narrow".
Link behind 7820A GC Remote Control Panel Revision 1.5.5.0 279 MB (current) on page above appears to lead nowhere (May 24). Grateful if this could be fixed. Thanks and regards
To learn more about each component take a look at the Concepts Guide manual included with your system and also Parts 2, 3, and soon 4 of this Blog post.
user-manual-msd-system-5977-concept-guide-G7077-90036-en-agilent.pdf
user-manual-tq-gc-ms-7000…
I'm curious to know how the voltage was applied to all the parts. I guess the repeller will be positively charged, and the lens are alternating and probably with RF to help focusing? But what about the ion source body? Is it grounded?
Also curious,…
If you have trouble viewing the content in the EQP files referenced above, refer to Part of PDF is blank when viewing in Edge, but not when I open in - Microsoft Community
Hi fgunawan , thanks for your reply. I did try with 100% IPA, but I didn't run the pressure test and leak test. I am new with the software and learning independently. I will try to explore these options.
Hi Linds,
Linds
Welcome to the Community. I think this is an excellent question, and something we all face from time to time. Thanks for asking!
I'm going to assume that you have a split/splitless inlet. A PM for this inlet usually includes a liner…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...