Thanks for this.
To make sure I'm understanding this correctly does this mean that the instant pilot is acting as the terminating end of the bus and that the socket that the instant pilot is connected to is the one that is failing when no instant pilot…
I have observed that when a method is transferred to a new system, you need to save it in the new system before using it. If you just copy the method and use it, sometimes it fails. Just by saving it, it makes it work. I guess it saves some defaults from…
We have an LC-MS with an Agilent 1260 Infinity HPLC stack, with a G7167A multisampler. The multisampler has one drawer installed with 2x 54-vial plates. We have had some communication issues recently where the transport initialistation kept failing after…
Hello, To cut to the chase: No, peak areas calculated in MassHunter will not be equal to the peak areas calculated in GC/OpenLAB ChemStation software. GC ChemStation and OpenLAB ChemStation use response units of pA for FID data whereas the response axis…
What are the detector voltages? Select the Hardware button, or Hardware/Dashboard from Task manager, and click the Detector image. Select EM setting. What are the voltages for Discriminator, Analog HV, and Pulse HV?
Was the instrument off, for an extended…
Hi, My method for 6890 GC/FID has a warning message that there are overlapping integrations for some of the compounds, I would like to correct this but unsure how, I know the answer lies in the integration events table. Any help is appreciated!
it does not work,
I tried to install openlab v2.4 manually, the installation failed at the agilent platform in the install or upgrade content management part,
Hi Lycrecia,
We checked the volume calibration section and we did the full range volume dispense, as described in the manual. However, we are not sure which value we should add to the actual volume in the volume calibration screen. Do we need to do…
It is great you have such a nice experience with your results, however results accuracy is a matter of hardware robustness and method setting, not software. I your insist on this, I can recommend you to do the following steps:
1- get the licence number…
The Agilent LabAdvisor software shows the Xe lamp life time, but in percent, not in hours. This is because of a fairly complex calculation, taking the amount of high or low power flashes into consideration. The higher the number, the more worn the lamp…
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer systems, RNA kit (15 nt) (p/n DNF-471-0500/1000), HS RNA kit (15 nt) (p/n DNF-472-0500/1000), Small RNA kit (p/n DNF-470-0275)
Issue
Which kit should be used to analyze single...
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx touch screen displays error code 90 after the Instrument Health Check (IHC), which happens when the AriaMx is switched on, or after running the onboard diagnostic tests...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx optical modules
Issue
AriaMx users can change which AriaMx optical modules are installed to upgrade the instrument capabilities or to troubleshoot.
Items Required
Any...
This Information Applies To: AriaMx real-time PCR system
Issue
Error 43 is displayed on the AriaMx touch screen. Error 43 is a voltage error and it normally indicates that the cartridge LED voltage or motor voltage being detected is abnormal. Sometimes...