You've got column in your column. A bad cut usually just results in tailing. Doesn't sound like the rear was touched, recut the inlet side and try again.
Hello,
No, you cannot create custom sample types in CDS. You can use an existing field like sample label to mark specific injections if you need more delineation than the sample types can provide.
Marty
Hello,
To check if you have access to a core facility in iLab, log into your iLab account and navigate to the core facility's page. If you are not prompted to request access and can view sections such as “About our Core,” “Request Services,” or “Schedule…
Hi Sabbas,
if you have measured a batch and click the print button, all method parameters are shown in the report. I’m not sure if you can print the report of method solely without having measured a sample. I would in that case just measure a blank…
Here a list of suggestions to try if encountering an error 155 on ELSD:
Make sure driver is at least A.01.07 DU1. Along with that, make sure the firmware and software is compatible with the driver.
Consider lowering the data rate (40 Hz if this…
As " alfausett " said, in case of headspace much depends upon sample matrix along with other factors. Honestly i am bit surprised that you are fine when injecting as liquid. In case of the liquid majority have issue with acetic acid peak shapes at some…
It all depends how old is your column or how it is handled when not in use. This is pretty much normal with majority of the columns when used in temperature programming. Some vendors claim to provide "zero bleed" columns but honestly there are many if…
This Information Applies To: Agilent OpenLab ChemStation
Issue
When launching OpenLab ChemStation Online or Offline session, the following error messages “ ChemStation ChemMain has stopped working ” or " There is a problem with Adobe Acrobat/Reader...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Agilent Femto Pulse, Agilent ZAG DNA Analyzer
Issue: The instrument encounters a run error, Run Aborted, Position fault: Did not reach target Z position ( Figure 1 ) . This error...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, Oligo Pro II
Issue:
This article explains the steps to take after installing a brand new array in the Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, and...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer systems, RNA kit (15 nt) (p/n DNF-471-0500/1000), HS RNA kit (15 nt) (p/n DNF-472-0500/1000), Small RNA kit (p/n DNF-470-0275)
Issue
Which kit should be used to analyze single...
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...