Hello staceylouie ,
I apologize for the delayed response.
The error you are seeing was a known issue in that revision due to no structure match being found for the selected compound. The workaround for that version was to click the Continue button…
Dear LD,
If your experiment requires precise control over calcium levels, EGTA should be preferred due to its higher selectivity for calcium ions. However, if calcium levels are not critical or can be adjusted accordingly, EDTA may be a suitable alternative…
Dirty, damaged, or blocked interface cones drastically impact the sensitivity and background of your ICP-MS system. Small/gradual changes in the vacuum level of the interface region is an indicator of cone maintenance. Learn about how to clean and condition…
Learn about how to inspect the torch, bonnet, shield plate, and RF Coil, as well as torch cleaning and handling recommendations for Agilent ICP-MS systems.
Preventative and regular maintenance are crucial in avoiding ignition issues and plasma instability…
Hello clockhar ,
The calibration table is stored in only one sample in the batch. This is why you keep seeing the same accuracy since this is stored in the peak table.
Unfortunately, it would be very difficult to come up with a Report Builder binding…
Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
Hello LC92 ,
Did you run the installer as an Administrator? That might cause issues like this.
Another thing to try is running the Software Verification Tool found in the Start menu under Agilent Technologies. See if there are any missing files. You…
This Information Applies To: Agilent Atomic Absorption Spectroscopy Systems (240/280 Series Flame AA and 240/280Z/Zeeman/GTA 120 Graphite Furnace)
Issue:
This article includes recommended maintenance procedures to be performed daily, weekly or annually...
This Information Applies To: Agilent SpectrAA Software, Agilent 240/280 Flame Atomic Absorption Systems, 240/280 Zeeman Graphite Furnace Systems
Issue:
How to Reset Lamp Usage Counters or Add a New Lamp in SpectrAA
Caution : All physical...
This Information Applies To: Agilent GTA 120, Agilent 240Z AA Spectrometer, Agilent 280Z AA Spectrometer, Agilent 240FS/GTA120/PSD120/UltrAA System
Issue:
It is important to align the sample probe of the Programmable Sampler Dispenser (PSD) 120...
This Information Applies To: Agilent Flame AA Systems: e.g., 55B, 240FS, 280FS
Issue:
The Flame AA burner and burner components require regular cleaning to maintain system performance. Components include the burner, nebulizer, and spray chamber...
This Information Applies To: Agilent Flame Atomic Absorption (AA) Spectrometers (50/55/240/280 AA)
Issue:
How to clean a blocked nebulizer of a Flame AA, which may be causing low sensitivity or a sample uptake rate below 5 ml/min.
Steps to follow...
This Information Applies To: Agilent Graphite Furnace Systems (PSD 120/GTA 120/240Z AA/280Z AA)
Issue
Maintenance procedure for replacing the syringe and plunger of the PSD 120 sample dispenser for the Agilent GTA and Zeeman Graphite Furnace Systems...
This Information Applies To: Agilent AA (AA240, AA280) with Graphite Furnace Accessory (GTA)
Issue:
The Programmable Sample Dispenser (PSD) requires the sampling probe to be accurately aligned before the PSD can be used.
The PSD enables the...
This Information Applies To: All Agilent AA systems: 55B, 240FS, 280FS, 240Z, 280Z
Issue:
Optimizing the position of the lamp maximizes amount of light from the lamp passing through the optics to the detector, improving the signal-to-noise and the...
This Information Applies To: Agilent VGA 77, AA, VGA 77P, ICP
Issue:
The Agilent Vapor Generation Accessories VGA 77 and VGA 77P use high concentrations acids. The system needs to be thoroughly cleaned after each use.
The Vapor Generation Accessory...
This Information Applies To: All Agilent Atomic Absorption Spectrometry Systems (AA50, AA55, AA240, AA280)
Issue: This article describes when and how to clean an AA burner.
Background
For optimum and safe performance, burners (see Figure 1 ...