Hello,
Recently, I've come across an issue where I performed a Lamp Intensity test using the Instant Pilot and it failed the 221-350nm wavelength. Since this is a relatively new lamp, I decided to look into values and that's where I saw Lab Advisor…
Hello,
We are currently running an Agilent 6460 QQQ LC/MS.
After a seemingly successful run we went to go analyze the data and found that all of our peaks had shifted considerably. We concluded that this might be due to the replacement of our inline…
Hi Using Openlab 2.4 with our 6890N GC. My question is how to be able to capture a Blank Run (no injection, only FIDsignal during oven ramping) ? In the training I understood that a "Double Blank" is what I needed. But when I make a sequence, with first…
Situation: User installed Openlab C.01.05 to run an LCMS system. Was able to configure the sytem, but when they launched they would see the following error in the initializing instrument phase: MSD Error 'Installl module, 'C:\Chem32\CORE\HPMSACQ0.DLL…
Hi all Wondering if a method can cause the IP adressess to get meesed up. I tried running a new method on an agilent 5975C MS with 7890A GC integrated with Gerstel headspace and FID.. the method did run but no data was collected. and worse, I believe…
Hi, what type of analysis are you running? For example is this pesticide analysis, residual solvents, etc? I'm also curious what type of sample matrix you are using.
A drop in transmission of 219/69 and 502/69 is typically related to the source. It…
Ok. So it sounds like some progress to get the negative mode tune to complete and look ok. I would run the negative tune only. Let it complete and save the tune file. Then run a positive polarity tune immediately.
If that fails again, its probably worth…
Hello Everyone, I'm new to Open Lab CDS and I currently have version 2.2 paired with a Agilent GC-FID. I'm still learnng the software and I had a few questions in regards to calibrating and calculating uncalibrated peaks. In Open Lab CDS, how do I calculate…
The front inlet on my GC8890 is failing the restriction test. It passes the leak test no problem and I've done everything I can think of to fix it. I've replaced the septa, checked the gold seal, trimmed the column, baked the column, and checked the inlet…
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software version B.02.08 or later
Issue
When printing a report to PDF or HTML with the 2100 Expert software, the error "Failed to Generate Report" appears.
Background
This error...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue
Resetting upper or lower markers from their automatically assigned settings in the Agilent 2100 Expert software.
Background
The Agilent 2100 Expert software...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert Software
Issue
Samples with a broad signal such as NGS smears should be analyzed by setting up a region. Analyzing a region is also termed smear analysis.
Steps to Follow...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RIN NA, Error 4501, RNA 6000 Nano kit (p/n 5067–1511 ), RNA 6000 Pico kit (p/n 5067–1513 )
Issue:
The RIN is not displayed in the software or shows as NA. If the RIN is NA, the...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RNA 6000 Nano kit (p/n 5067-1511), RNA 6000 Pico kit (p/n 5067-1513)
Issue:
Which assay should be selected in the Agilent 2100 Expert software when running yeast total RNA samples...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software, RNA assay, DNA assay, Protein assay
Issue:
The X-axis description toggle icon in the Agilent 2100 Expert software toolbar ( Figure 1 ) does not change the X-axis from time...