Error : Data Subscriptions Failed. Are inbound Ports Blocked? Is there Right Type of GC at IP Address? GC does seem to be connected but not the MS. Does anyone have suggestions on what the problem might be?
Try to reinstall using the ChemStationSystem account. If that fails, try the following before installing. 1. Delete the ChemStationSystem account. 2. Delete the chemstaion.ini file located in the Windows directory. 3. Log in as the Administrator and install…
I see the green lignt ON on the logic board. I never see it is blinking though. Thank you for sending the document. Once I tried ping from another PC with firewall off, but ping got failed. I will try ping from that PC after reading the document.
The…
Hi All, We are experiencing a very strange issue (very broad peak) with Dimethyl Formamide Solvent when run with one particular residual solvent method utilizing Dimethyl Formamide as Diluent. Method has been run for the past 4/5 years without any issues…
Autostart Macro failed, error# 999 occurred (OpenLAB CDS Chemstation Rev. C.0x.0x) This is usually resolved by resetting the instrument configuration files in the instrument folder (\Chem32\x\, where x is the number of the instrument in question). Append…
We recently purchased a GS Oxyplot column based on its reported excellence for separating oxygenated compounds in hydrocarbons streams such as Ethylene, which is required to be of ultra high purity for polymerization catalysts. Unfortunately we see a…
Hi everyone, A few weeks ago in our lab we installed a new inlet/column/detector set-up on an existing 7890B GC in our lab. This GC already had a front inlet/detector installed and there was never anything installed on the back components. Therefore we…
Hi evryone
Please help: i just get these 2 messages which make me i can not inject from my 7890A and 5973C MSD " tune action stopped: cannot achieve constant peaks widths " also "limits fail: pump oils (days), tune time (hours) at the same moment the…
I don't know if this applies to your specific problem, but a lot of failed uploads and other problems can arise because the GCMS users don't have the proper privileges in ECM. Below is an image with the proper privileges. Assigning the ECM Contributor…
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...