• Created : 
  • Modified : 
  • Category :  Agilent Knowledge Portal
  • Entry Type :  Article
  • Product Type :  Analytical LC Systems Preparative LC Systems
  • Component :  LC Detectors
  • Product Name :  1100 Series LC System 1120 Compact LC 1200 Series LC System 1220 infinity II LC System 1260 Infinity II Bio-Inert LC System 1260 Infinity II LC System 1260 Infinity II Prime Bio LC System 1260 Infinity LC System 1260 Infinity II Prime LC System 1290 Infinity II Bio LC System 1290 Infinity II LC System 1290 Infinity LC System
  • Task :  Troubleshooting
Related Articles

  • How to Check, Configure and Use the IP Address of an Agilent HPLC Module

    This Information Applies To: All Agilent (U)HPLC modules. Issue: This article describes the general procedure of how to check the IP address of an High Performance Liquid Chromatography (HPLC) module and how to modify it using Telnet. Agilent HPLC modules can be configured to use either a default IP address (192.168.254.11) that cannot be changed (static), or a stored IP address that can be defined by the user. The position of the configuration switches that are on the back of an LC module...

  • New UV Lamp Not Working - Lamp Tag Not Ready Error

    This Information Applies To: Agilent Variable Wavelength Detectors G1314D, G1314E, G1314F, G7114A/B, and Diode Array Detectors G1315C, G1315D, G7115A, G7117A/B/C. Issue: When using UV lamps that do not have the RFID tag built in, the VWD and DAD modules may deliver an error upon exchanging the lamp. Errors can include "UV lamp tag not ready", together with the normal status "UV lamp not ready". This article describes how to resolve this issue. Steps to follow: Go to instrument status...

  • Quick way to Manually Determine Gradient Composition Accuracy

    This Information Applies To: Agilent LC Pumps Issue If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick way to determine if the pump can accurately proportion the requested composition. The test is done by manually changing the composition and noting the responses. Note: This procedure can only be done with a UV detector, not valid for non-UV systems...

  • How to Install a Max-Light Cartridge Cell?

    This Information Applies To: Agilent LC Systems with G4212x / G7117x diode array detectors (DAD) Issue The Max Light cartridge flow cells have small internal diameter inlet and outlet capillaries. As a consequence, particles can easily block the capillary with some application/ practices, or using a dirty column, dirty solvents, or by flushing the system through the flow cell. If it is leaking or if the intensity drops due to a contaminated flow cell, the cartridge needs to be replaced. ...

  • Removing a Clog from a Flow Cell

    This Information Applies To: Agilent UV and RID detectors Issue A clogged flow cell causes high backpressure. The clog can be removed by flushing the system with solvents at high pressure. If you suspect a clog or experience high backpressure due to the flow cell follow the procedure below. Steps to follow Before proceeding: Disconnect the column and replace with a union. Caution : If the column is left in the flow path, it may be damaged during the flushing procedure...

How to Flush an HPLC Flow Cell to Troubleshoot Baseline Noise

Answer

This Information Applies To: Agilent UV LC detectors: Diode Array Detectors (DAD), Multiple Wavelength Detectors (MWD), Variable Wavelength Detectors (VWD)

Issue

The following procedure is recommended to flush a dirty flow cell and remove baseline noise.

 

  
Caution: disconnect the column before following the procedure. Place a Union instead of the column.

 

Requirements

  • Reverse the cell flow path by swapping the inlet and outlet lines. 
  • If you suspect a clog or a partial obstruction of the cell, normally associated to an increase in pressure, follow the procedure described at this link first.

Steps to follow

Reversed phase applications

  1. Open the Purge Valve of your pump. Set a flow of 5 ml/min and purge each channel for 5 min with HPLC-quality Water. During step 1, check that the solvent moves into the solvent line correctly and it goes out the Purge Valve. If it does not, check the state of the Solvent Filters and replace them.
  2. Close the Purge Valve and flush the system. Set the flow rate at 1 ml/min. Let it run for 1 hour, with HPLC-quality Water. Make sure that the pressure does not exceed 60 bars during this step.
  3. Flush the system with 100% Isopropanol (IPA) 1 ml/min, for at least 1 hour. Make sure that the pressure does not exceed 60 bars during this step.
  4. Repeat step 2 then continue with step 5.
  5. Swap the inlet and outlet lines of the cell flow and equilibrate the system with your solvents.
  6. Check if the baseline issue observed initially disappeared. If so, reconnect the column and proceed in using the system. If the issue persists, please contact Agilent Technical Support.

Normal phase applications

  1. Open the Purge Valve of your pump and purge each solvent line, one by one, with HPLC-quality Isopropanol (IPA). Set a flow of 5 mL/min and purge for 5 min. During step 1, check that the solvent moves into the solvent line correctly and it goes out the Purge Valve. If it does not, check the state of the Solvent Filters and replace them if needed.
  2. Close the Purge Valve and flush the system with IPA and a flow rate of 1 ml/min. Let it run for at least 2 hours, with HPLC-quality IPA. Make sure that the pressure does not exceed 60 bars during this step.
  3. Swap the inlet and outlet lines of the flow cell. 
  4. Equilibrate the system with your solvents. 
  5. Check if the baseline issue observed initially disappeared. If so, reconnect the column and proceed in using the system. If the issue persists, please contact Agilent Technical Support.
 Tip 
Learn how to effectively troubleshoot your Agilent UV Detector:
HPLC-0GEN-2201e - Chromatographic Troubleshooting for HPLC e-learning course available from Agilent education

 

 
Was this helpful?
Privacy Statement
Terms of Use
Contact Us
Site Help