We have recently replaced the ESI needle on our Agilent 6100 LC-MS. All is well with the flow, but we are not able to tune our instrument. Last week, the tune looked fine, but since replacing the needle the peaks (118, 622, 922) are not found and we get…
Can Someone help me in converting below logical statements to IR. Statement IF Assay>99 And Assay<101 ,Then "Pass" Otherwise Display "Fail" Syntax I used =Iif(99<Assay<101,"Pass","Fail") But results I am getting as below Always Pass Thanks & Regards Rajesh…
Hi Erik, This depends on the version of G2070AA or BA. The below may help. The Autostart Macro failed, error# 999 occurs on startup of the Chemstation if the Initial Screen Window Size is set to “Icon” in the Configuration editor. In the PCS section of…
Last week we vented and powered off our Agilent 6650 iFunnel QTOF. When we tried to turn it on and pump down from mass hunter software (I think B 09), the rough pump ran at the beginning, but just after 10 min, then it automatically stops. After a couple…
We have backup generation, and we also recently put all of our instruments on a full-pass UPS system (Weissco Power - www.weisscopower.com) All power to each instrument goes through the UPS system. The nice thing about the system we have is that the power…
Hello and thanks for your quick answer! I would like to come back to my starting question: if i use macros i can not find the changes from the chemstation in the documentation. For example (one question from above): In Version C.01.10 the Sequence is…
Hi azrael, Thanks for the clarification. If the ground is not functioning at the outlet, the metal of the GC cannot be grounded. This means anything that was touching the metal chassis of the GC could have been subjected to the full line voltage - lots…
Dear All! A customer would like to do the following (I already advised them about blank subtraction but it is not what they want): How to deduct blank peak area from sample (or standard) peak area What the customer has already done: CC1: to get the blank…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...