Yes, it is the constant flow mode. The following is the method I am using: Carrier gas: Helium Carrier gas flow rate: 1 mL/min (constant flow) Injection volume: 1 μL Injection port temperature: 250 °C Split injection ratio: 30:1 Initial oven temperature…
The degasser in our G7112B failed (diaphragm in the vacuum pump tore) and I swapped it out with a spare G1311A/G1379 combo while we wait for parts/repair.
Everything is connected and configured properly, the instrument config in OpenLab CDS 2.3 has…
Hello, The tune evaluation on the 5977B GC-MS is failing. The reason is 502/69 mass ratio is smaller than 2.4 (reading = 1.5-2.0), more specifically the 502 m/z count is around 7000-9000, instead of 20000 which is seen in previous autotunes. I cleaned…
This can happen when one of the motors on the arm of a vial sampler (G1313, G1329, or G7129) is failing. It will be fine for a number of injections, then one of the motors gets too hot from all the movement and will cause the sampler to error. When you…
Yes, that what I was looking for. But in the same time, we realized that Office 2016 is able to correctly open "coma" or "semicolon" separeated .csv, where Office 2010 fails and only opens one format correctly. So we're looking at this option as well…
How long is your "electricity problem" ? And what is it? A switchover or a full-on power fail or?
Agilent does not support GC or GCMS on a UPS as too many UPS cannot handle the high amperage load. See: (+) Use of a UPS to Supply Power to an Agilent…
We have Agilent G1312B, 1367C autosampler and G1316B column compartment, we just installed openlab C.01.09 into our surface book laptop with window 10 pro, when we did the installation, system check found some problems, such as power options and window…
We are trying to resuscitate a G1956A MSD. Recently replaced power supply which got the heaters working but MSD still not ready. On running diagnostics, got an MS Ion Optics Test Failure: Ramping Test Error: Not enough signal at m/z 1218 for ramping test…
Rapid through-barrier raw material identification
Point. Click. Get a pass or fail result.
It almost seems like magic at first, a workflow so simple it begs the question, why do it any other way? Through-barrier raw material identification is an absolute…
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...