Hi Kris, thank you! I tried to upload the screenshot of the version info, but I failed. So I have to type all of them out since I'm not sure which one is useful. Hope it can help!
Agilent OpenLAB Intelligent Reporting A.01.11.138
Agilent OpenLAB CDS…
Hello,
upon start vacuum sequence. You should hear a clik. This is for BK. Monitor IF/BK meter at that point. it has to go lower than 20 Pa. Then you should hear a second click. This time another valve open. It should rise above 20 Pa. Then after…
I don't think it would have a problem as long as you're not trying to connect with both software platforms at the same time. I've seen other customers do similar things (GCMS/FID, using MSD Chemstation for MSD work and GC Chemstation for FID work).
Tray sensor failed is either try a new tray or the transport assy is most likely needs to be replaced. Does Lab Advisor see the module? There is a log book in Lab Advisor as well.
Hi All, I'm trying to get the following expression to work in a Qual 10 report (in excel format as that's about the extent of my coding knowledge): =IF(Area<DB_Notes,"Fail","Pass") to flag compounds which are less than a defined minimum peak area (which…
The Digest of upcoming webinars has been updated as of December 13.
Notable additions include:
Atomic (4)
GC & GCMS (9)
Vacuum Solutions Series (1)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from…
Good morning,
We have an Agilent 7820A GC-FID equipped with a G4567A autosampler.
In the middle of a sequence, the system gave the following errors:
ALS Failure State: Preparing Samples
ALS Failure Code 945 : Autoinjector back tower plunger…
Are there electronic checks that can check to make sure a filament isn't failing because of an electronic issue? We had a filament die, which isn't too surprising considering it was nearly ten years old (teaching institution, the instrument sees periodic…
Good morning It turns out that this is the first time something so particular has happened to me with my GC-MSD (6850-5975). I work with MassHunter 10.0.368 and from one moment to another the signal for two of my work standards (organophosphates and phenols…
I work in a small, environmental lab. We test aluminum levels in serum using ICP-MS. We can run batches of 250 samples at a time. We dilute 500 microliters of serum to 5 ml using 0.2% HNO3. We calibrate using 1, 5, 10, and 20 ppb Aluminum std. At the…
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
Early Maintenance Feedback is a useful feature on Agilent GC Systems and software that allows a user to monitor the maintenance needed on their GC. This feature allows for users to...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue:
This procedure outlines the steps to view and clear the maintenance warnings on based on Agilent 8890/8860 GCs. You can also follow the onscreen instructions to perform maintenance...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with Agilent MS-40+ rotary vane pump.
Issue
Regular check of the rough pump fluid level in your MS40+ pump as part of regular 6000 LC/MS system maintenance checks.
Steps...
This Information Applies To the Following Products : All Agilent iFunnel and Agilent Jet Stream (AJS) 6400 Series LC/MS triple quadrupole systems, Agilent 6460A/C, 6470A, 6490A, and 6495A/B/C
Issue:
As LC Triple Quadrupole Mass Spectrometers (LC...