Hi everyone, My MP-AES 4210 Machine sa is failing to suck/take-up the samples from the sample tubes..
I tried changing the sample pipes but nothing worked. Kindly asking for help on how to sort out this problem?
Regards,
Kalunga
Hello!
It would be very good to get step by step instruction and definition of each row on Splitter calculator and other calculators to configure our system.
The system uses SCD and FID detectors.
Target is to get ratio 3:1 between SCD and FID for…
Dear team,
I'm running 8890 GC-FID using back injector and front Detector FID. When, we uploaded sequence table, there's message appearing that sequence table rear injection isn't detected. Can anyone help to advise what to do with that?
Thanks…
hi all,
we have ICP-MS 7800 and getting error 1445. The content of the error is as follows:
"1445, Error: Plasma gas flow rate is too low." We can't ignite plasma.
Gas valves and gas line have been checked and there is no problem.
Does anyone…
My knowledge of GCs is extremely limited. Currently we analyze for n-pentane only. The program was already set-up when I started working here.
Yes, an FID is present
1. Sampling vessel type unknown at this time.
2. I am expecting the range to be…
I have the flex metal G3188-27501 ferrules. when it comes to the Inlet, the ferrules fit alright and I can tighten them onto the column. When it comes to the FID port, the ferrule is too long and I can't screw in the column to the outlet. If I really…
While removing a column from an Agilent mass spec 5977B the column broke off and I can't figure out how to remove it. I'm using MassHunter version 10.1.64.1 (12/15/2021) but not actually using the mass spec but only the FID on the back. If I start a sequence…
How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...