Please give more information. TSU - is that Thermal Screening Unit? You say under varying pressures...from zero to how many PSI/Bar? Will you need to use a vacuum to get the sample? Will this be analytes in air or something else? Decomposition of what…
Did the EM get replaced March 15? Or a source cleaning? The EMV went down 883V.
The Ent Lens (Entrance Lens) those jumps from 16 to 63,32,47.5 .. and the Ion Focus going from 80's to 40's... make me jumpy. Something was changing. When were source cleanings…
The ID testing process in the pharmaceutical industry often exposes warehouse staff to hazardous materials. This new technical note shows how pharmaceutical manufacturing QA/QC organizations can use the Agilent Vaya Raman system to check raw materials…
Hello community,
I have the following error (attached images) when start either offline or online mode. As you can see, the module control panel also dissappear. I have checked all the conections between PC and all modules and the error window continue…
Recommendations updated after looking at this version from February 16, 2023. The recommendations are pretty much the same as above.
Increase the oven temperature equilibration time to 1.0 to 1.5 minutes or longer. It takes time for the 240° oven post…
We attempted the same testing on another OL2 instrument and the sensitivity issue was not present. It was unique to a single system. Agilent was very helpful getting us another system to test on. It seemed to be related to the tune/threshold/filtering…
Hi,
1. This is the "Easy Fit Lense Assy" - Since two years, we (Agilent) has decided not to clean the lenses, but to replace them completely. So if you want to disassemble these, you have to break the plastic cap, and use a screw set from an older regular…
Hello,
You would need to look into the other logs to see the issue in more detail. The details logs are in a Microsoft log format and required a viewer download. I would suggest opening a ticket with your local Agilent support group. It does look…
Hello,
I cannot give you a direct link for the software. You would need to use the Agilent subscribenet to download any software where you have an entitlement. This would be any software you have registered with the site for licensing in the past…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...