I have just received the Agilent Cary 60 UV-Vis photospectrometer and while following the steps to install the software i receive and error pop up which says "failed to register Class not registered" this occurs no matter what software i try apart from…
Hi everyone,
I've an issue with the fragment analyser (5200) my migration is aborted because the µA target is not achieved (4 instead of 5-1500µA).
The error log is called "HV supply" and I've notice that the little light "HV ON" is not turned on…
Thank you for your help! I will definitely keep in mind. Where is the small and large cover? I will look for the switch breaker at the back. I think it might be the Ar problem, during the 2 to 3 ignitions, the pressure meter on the Ar cylinder dropped…
Working with MassHunter 4.6 Workstation Software for 7900 ICP-MS, G7201C, version C.01.06, Build 621.2
I have a first order calibration with no evidence of any issues (%RE are small and random), but the end client has asked for a 1/x weighting to be…
Hello, I've been using an infinity 1260 autosampler and sporadically during injection I get the error: "Sampler G1329B:DEAAC21082 - Valve to bypass failed [EE 4014, 0]. This causes the system to disconnect and terminate the run. I can restart the entire…
Hi,
When self test on DAD G7117C with 10mm MaxLight Flowcell is performed, it fails because of the spectral flatness (measured 3.3587 AU and limit is 0.002 AU).
Whats exactly calculated in spectral flatness? What could be a reason that this test fails…
We want to connect the output of one column to a splitter and then connect the outputs of the splitter to an MSD and a FID. Is that possible? The MSD worksin vacuum and FID toatmospheric pressure, then the effluent will be sucked by the MSD and there…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
This Information Applies To: 1100, 1200 and 1260 Infinity I and 1260 Infinity II LC Pumps (Excluding preparative pumps with electromagnetic purge valve (EMPV): G1361A. Not applicable to any of the 1290 Infinity II modules with automatic purge valve: G4220X...
This Information Applies To: Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules
Issue:
Removing and re-installing Visible and UV lamps in Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules.
Both the visible and UV lamps are consumable...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pumps.
Issue:
Removal of the pump head from the pump metering drive for maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Module.
Steps...
This Information Applies To: All Agilent 1260 Infinity Binary, Quaternary, or Isocratic Pumps without the Seal Wash Option installed.
Issue:
Worn pump seals can shed small particles that can cause blockages and pressure issues downstream of the...
This Information Applies To: Agilent G7167x Multisampler modules
Issue:
Required when:
The needle seat is visibly damaged, blocked, or is leaking.
Leaks or blockages in the Vialsampler are observed, especially between the needle and needle...
This Information Applies To: Agilent 1260 Isocratic (G1310B) Quaternary (G1311B) Pumps.
Issue
Required when:
The inlet valve is defective.
The pressure or leak test in Lab Advisor suggests the inlet valve may require replacement.
A large...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
Required when:
The outlet valve is defective or leaking.
The pressure or leak test in Lab Advisor suggests the outlet valve may require replacement...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
The seal wear in procedure is important as it acts to "bed-in" the seals to ensure a leak free and pressure-tight pump head.
Required when:...
This Information Applies To: Agilent G7167A/B Infinity II Multisamplers
Issue:
The Agilent Multisampler autoreferencing procedure uses predefined positions on the base plate and the sample hotel to calibrate the positioning of the needle parkstation...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Modules
Issue:
Reinstallation of the pump head on the pump metering drive during maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump...