I'm not experienced in FID so I'm not sure what normal bleed looks like. So yes I would trim the column and check for leaks first then a new column. Can you look back at older runs when this column was installed to see what the bleed looks like to compare…
Thank you for your response. I really appreciate your help. I realized I didn't provide clear information about the experimental conditions. Here are the specific conditions:
Inlet temperature: 250°C
Column oven temperature: 150°C (isothermal) …
Hi
I am trying to install the G7201D version of ICP MassHunter on a 1909 Windows 10 laptop.
It goes through the initial process and then errors with a code of 0xe0434352.
Some additional research implies this is a .Net error but a repair install…
Dear All,
We are using NGA analyser as per GPA 2286 method using FID and TCD.
Could you please advice how to apply the bridging to correct the concentration from FID.
Hi again Raina,
as I already told you this cannot be done with just one column, especially with the CO2 concentration up to 20% and water included and the necessity to analyze H2. This is an application we normally build an analyzer for. You need at…
In an official Service Note we say "According to our lamp manufacturers there is no shelf life for LC detector deuterium (D2) lamps. Our logistic centers (LC) try to ship lamps from stock before they reach 12 months age. We see the lamps lasting for more…
When you run startup, does it use the Standard Tune or User Tune? In the new D rev of software (5.X) you can go to Startup/Startup Configuration and just above the Hardware settings table select Configure ignition sequence. For C rev (4.X) click the narrow…
I have a MicroGC 990. Seemingly out of no where, the following error has popped up after hitting Control -> Single Run on a method we've been using for months:
Failed to submit "D:\ .... path name .... (GMT -04-00).seq" for acquisition.
Please resubmit…
What version of Windows do is it running? Go to the cell next to the logo (Type here to search) and enter winver and select the run app. At top it should say Windows 10, at this time only MassHunter 5.2 is Win11 compatible. 2 lines below Windows 10 will…
Hi guys, when I tried to run my sequence in GC-FID, the workstation showed "front injectors not detected", and under my method, the configuration showed no injectors. However, the parameters I entered for injection could be found in the GC (7890A) operation…
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...
This Information Applies To: Agilent OpenLab CDS Software (ver 2.x).
Issue:
This article will give instructions on how to submit a single sample run in the OpenLab CDS Software.
Steps to follow:
Launch the acquisition software through the...
This Information Applies To: Agilent OpenLab CDS products
Issue:
Every computer running Agilent OpenLab CDS Software requires a unique software license for continuous operation. Failure to install a valid license will cause the instrument control...