Hello,
I am not sure exactly what you are doing but to use part of the text in an if you can parse apart the text using string functions or use the like comparison. So your =IF(COUNTIF( A2 ,"*mg*"),"Value if true","Value if false") would be =If(A2…
How many total runs on this system?
8890 and Intuvo: Service Mode, Instrument, Usage
7890: Service Mode , Diagnostics, Instrument Status
6890: Options, Diagnostics, Instrument Status
A 6890/5975 probably has many, many runs on it and passed…
There could be issues with either control signals to the HED power supply or the power supplied to the HED power supply. These electronic issues are down in the depths of the instrument and should be handled by a trained service engineer. Please contact…
A bit late maybe, but you can set the printer within the macro using the MYPRINTER = "name of printer". Use the command before your STARTPRINT command, and then at the end of the macro remove it (REMOVE MYPRINTER), so that it will only be active for the…
Here's a link to the video from this event!
(+) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion - Forum - Gas Chromatography - Agilent Community
You should always consider that after re-igniting the lamp, it typically requires 60-90 minutes establishing a stable detector signal.
Based on this it does not always make sense and saves lifetime shutting off the lamp.
Keep constant flow 1.2 ml/min into the MS and do a Pulsed Splitless injection, tips in the help section of the Operating manual. Your system's diffusion high vacuum pump can only handle 2.0 ml/min maximum so do not exceed that ever.
If you have a 30m…
In Manual Tune, PFTBA closed, set the scan range to 10-100, then click on the spectrum scan button. The spectrum will show repeatedly in the middle window to the left at the long red arrow..
Beautiful. Does the spacing change with a different column flow rate? If this is 1.2 ml/min, for example, is it different with only 1.0 ml/min? If it changes and you did the inlet and column maintenance properly, the issue is before those. If it does…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...
This Information Applies To: Agilent CI Source
Issue:
During normal operation of the GC/MS, the CI ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or routine replacement of consumable parts (filament and...
This Information Applies To: Agilent OpenLab CDS
Issue
This article will explain how to add a sequence summary report line to a sequence, in Agilent OpenLab CDS, as well as how to configure it so it matches your reporting needs.
Background ...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS ChemStation, OpenLab CDS EZChrom.
Issue
Process for creating a desktop shortcut for your instruments, with OpenLab software, to enable quick access to your acquisition window.
Background...
This Information Applies To: Agilent LC Systems
Issue
Agilent modules will go into an error status (red status light) when an error condition specific to that module occurs. For example, metering home failed will be specific for the autosampler...
This Information Applies To: Agilent Analytical LC Autosamplers
Issue
To increase the maximum injection volume of an autosampler, there are two ways to do it. While both will provide larger injection volumes, there are advantages and disadvantages...
How to Recover a SubscribeNet Password
Multiple Results
This Information Applies To: Agilent Software products with SubscribeNet license.
Issue
Resolutions for password recovery use if you have: lost your password, been locked out of the account, or you don't know if you have an account with SubscribeNet...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS EZChrom
Issue
Steps to create a Data Analysis shortcut for one or more of your Projects defined in the OpenLab Control Panel .
Steps to Follow
Open the Control Panel of your...