Hello Martin and Andy! I found out what were wrong. In my sequence two injections doesn't have a DA Method linked. When I pin only the injections with DA Method linked, the "No Data Found" was gone.
Thanks for letting us know. I will look into this and determine why it is not working. In the meantime, the file can be downloaded from the 7820A product page at https://www.agilent.com/en/product/gas-chromatography/gc-systems/7820a-gc-system . Scroll…
Thank you very much for your quick answer. It's very important for me to understand the concept well, so I have some consistency problems with the response of the compounds.
The Digest of upcoming webinars has been updated as of May 23.
The new Agilent Community Group, GPC/SEC Solutions Group hosted a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules …
For more information, check out the application note Five Keys to Unlock Maximum Performance in the Analysis of Over 200 Pesticides in Challenging Food Matrices .
Recommended parts from the video:
Self-tightening, collared column nut for use with…
Hello,
Are you still having low flow issues on your AA? Did replacing the nebulizer assembly help?
Do you change the flame gases for your methods? If so, call up a default air/acetylene method. You will need a lamp of that element. Go to Optimize…
It is hard to see from the picture which stator this is. If it is the 7 port for ISIS3 then the part number of just the stator is:
G8411-80121 Stator, for 7 port, 2 position inject valve.
Hello,
The penning gauge is now referred to as the ion gauge. It is located on the right side, front of the analyzer chamber. It is easily identified by the blue cable connected to the back of the gauge. Make sure to put the instrument into Shutdown…
This Information Applies To: Agilent CI Source
Issue:
During normal operation of the GC/MS, the CI ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or routine replacement of consumable parts (filament and...
This Information Applies To: Agilent OpenLab CDS
Issue
This article will explain how to add a sequence summary report line to a sequence, in Agilent OpenLab CDS, as well as how to configure it so it matches your reporting needs.
Background ...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS ChemStation, OpenLab CDS EZChrom.
Issue
Process for creating a desktop shortcut for your instruments, with OpenLab software, to enable quick access to your acquisition window.
Background...
This Information Applies To: Agilent LC Systems
Issue
Agilent modules will go into an error status (red status light) when an error condition specific to that module occurs. For example, metering home failed will be specific for the autosampler...
This Information Applies To: Agilent Analytical LC Autosamplers
Issue
To increase the maximum injection volume of an autosampler, there are two ways to do it. While both will provide larger injection volumes, there are advantages and disadvantages...
How to Recover a SubscribeNet Password
Multiple Results
This Information Applies To: Agilent Software products with SubscribeNet license.
Issue
Resolutions for password recovery use if you have: lost your password, been locked out of the account, or you don't know if you have an account with SubscribeNet...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS EZChrom
Issue
Steps to create a Data Analysis shortcut for one or more of your Projects defined in the OpenLab Control Panel .
Steps to Follow
Open the Control Panel of your...
This Information Applies To: Agilent 6100, 6200, 6400 and 6500 LC/MS Systems
Issue
Error on the Mainboard reporting “Leak Detected”.
Background
The fault “Mainboard #1: Leak Detected” is reported in the Data Acquisition Software Logs ( Figure...
This Information Applies To: Agilent LC/MS Systems
Issue
The MS solvent selection valve (SSV) rotor seal is replaced annually as part of the Preventive Maintenance. It can also be replaced as part of troubleshooting a leak, a flow blockage, or when...
This Information Applies To: All Agilent HPLC modules.
Issue:
The firmware is stored on a HPLC module's mainboard. It's a set of parameters, low-level commands, and functions stored on the internal memory of a HPLC module and required for its operation...