Hello E_Johnson ,
I’m sorry for the delayed reply to your message.
Thank you for asking this question. Always refer to the applicable Agilent instrument safety information when performing instrument maintenance or repair ( 7890 Series GC Safety Manual…
Hi we are now using masshunter quant to process the data of gc/fid obtain by openlab cds and then using gc translator.the multiplier has already been set in the sequence table.and is there a way to obtain it from the masshunter in the batch table.so the…
Hello!! When running HPLC, I am receiving the following warning which prevents my sequences from running: "DAD method download failed for module G4212B:DEAA303287! Use Signal is not allowed to be changed during run." I am receiving this warning when I…
Hi, i want to update the Firmware of an 5975C with the Firmware Update program msupdate.exe of OpenLab to Version 7.02.29. At the moment the version is 5.02.09 and this version doesn’t support the new OpenLab. Unfortunately the update aborts at one point…
Dear all,
we just recently received an upgrade from OpenLab 2.3 to 2.7. We control a Shimadzu with OpenLab. The Shimadzu GC-FID received a new set of drivers during upgrade.
We are now running into problems during calibration of our runs which were…
Hello,
I had my 6890 Plus GC connected to Chemstation B04.02 through a G1369B LAN card recently. Today I had a warning #103 "Sig 1 buffer full" shown in the GC display, probably because the PC went to saver mode over the past couple of days. I restarted…
I'm using the GC6890 with one single column (CP7429). The gas products have to be analyzed by TCD and FID simutaneously. How should I connect the column to TCD and FID? Is it necessary to have a s plitter to split effluent from a single column to TCD…
Hello scientists, I need help
I am using an MP-AES 4200, It worked perfectly until we had a power interruption. Ever since it has kept giving errors such as
1. Plasma Failed to ignite. This may be due to a low supply of Argon or Nitrogen, a deteriorated…
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...
This Information Applies To: Agilent 7693A, 7650A, and 7683 Series automated liquid samplers
Issue
GC software or GC LED display shows ALS Failure code 245: Autosampler front tower plunger error or ALS Failure Code 945: Auto injector back tower...
This Information Applies To: TapeStation ScreenTapes and reagents
Issue
Using the search tool on Agilent.com to locate the declarations of conformity (DOC) for Agilent ScreenTapes and Test-Tapes, certificates of conformity (COC) for TapeStation...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The Automatic Liquid Sampler (ALS) system calibration process aligns the sample tray with the injector turret position to enable vial transfers without incident.
Calibration...