Hi.
So ive had a very high sample with Methanol (around 8000 mg/l) and now i still have contamination around 500 mg/l in my blanks. Ive tried injecting IPA and replaced the syringe. Any other tips? Ive also pumped up the oven/column tempature to a…
5 psi inlet pressure running hydrogen with your configuration leads to 2.3 ml/min to the MS and 1.02 ml/min to the FID.
You are welcome. Are you using a two-hole ferrule in the injection port or a splitter of some type? The two-holed ferrules are..…
Canadian_Chemist ,
There is an example of printing text instead of the final concentration based on the LOQ outlier in this discussion.
(+) Report builder - Final Concentration Expression Change - Forum - Mass Spectrometry Software - Agilent Community…
Yes, it is off on all gasses, always by roughly 20% (occasionally nearly 30% or as low as 15%, depending on the instrument). Air, Hydrogen, Makeup (N2), carrier (H2 or He) on every instrument (12 GC and 3 GC/MS, which haven't been evaluated). It's also…
Hello,
3-way valve is a good idea, but unfortunately all I had was several 5180-4160 Tee, 1/8 in, brass, and several 0100-2144 Ball valve, 1/8 inch.
So I decided to make following setup.
In the setup below I am using He as carrier gas and N2 as…
When trying to close a connection on an instrument with an active single run or sequence the OpenLAB CDS software will usually give a message that it will close connection when the runs are finished. Today when trying to close 2 instruments on the same…
Hello Agilent Users,
Im missing a feature in Openlab since day 1. How do I override and start a run if the GC is not ready ?
For example: the FID temperature is set at 250°C in the method and the actual temperature is at 220°C (it is still heating…
Hi,
My baseline is around 8pA in standby state. H2 is coming from a tank and I can rule out contaminations in the gas source because the gas line is splitted with T piece: one is going to the FID EPC and one is going to the inlet PCM. H2 is the carrier…
Hi all
Apparently the engineer who did the mainboard replacement made a mistake by plugging the MCGV cable to the SSV cable, this made the valve failed to switch (EE 2040.2) and electronic fuse of SSV (EE2049.0) error always appear. It was out of my…
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...
This Information Applies To: Agilent 7693A, 7650A, and 7683 Series automated liquid samplers
Issue
GC software or GC LED display shows ALS Failure code 245: Autosampler front tower plunger error or ALS Failure Code 945: Auto injector back tower...
This Information Applies To: TapeStation ScreenTapes and reagents
Issue
Using the search tool on Agilent.com to locate the declarations of conformity (DOC) for Agilent ScreenTapes and Test-Tapes, certificates of conformity (COC) for TapeStation...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The Automatic Liquid Sampler (ALS) system calibration process aligns the sample tray with the injector turret position to enable vial transfers without incident.
Calibration...