Hi
I have one problem with my 5977B.
The tune no finish, the principal problem or error is "Tune action stopped: Gain and offset = 0 and peaks are too narrow".
Link behind 7820A GC Remote Control Panel Revision 1.5.5.0 279 MB (current) on page above appears to lead nowhere (May 24). Grateful if this could be fixed. Thanks and regards
To learn more about each component take a look at the Concepts Guide manual included with your system and also Parts 2, 3, and soon 4 of this Blog post.
user-manual-msd-system-5977-concept-guide-G7077-90036-en-agilent.pdf
user-manual-tq-gc-ms-7000…
I'm curious to know how the voltage was applied to all the parts. I guess the repeller will be positively charged, and the lens are alternating and probably with RF to help focusing? But what about the ion source body? Is it grounded?
Also curious,…
If you have trouble viewing the content in the EQP files referenced above, refer to Part of PDF is blank when viewing in Edge, but not when I open in - Microsoft Community
Hi fgunawan , thanks for your reply. I did try with 100% IPA, but I didn't run the pressure test and leak test. I am new with the software and learning independently. I will try to explore these options.
Hi Linds,
Linds
Welcome to the Community. I think this is an excellent question, and something we all face from time to time. Thanks for asking!
I'm going to assume that you have a split/splitless inlet. A PM for this inlet usually includes a liner…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
You should be able to but best to get customer care in your region to confirm they can advise on both options. The MS40 upgrade is the better option if you can go for it.
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...
This Information Applies To: Agilent 7693A, 7650A, and 7683 Series automated liquid samplers
Issue
GC software or GC LED display shows ALS Failure code 245: Autosampler front tower plunger error or ALS Failure Code 945: Auto injector back tower...
This Information Applies To: TapeStation ScreenTapes and reagents
Issue
Using the search tool on Agilent.com to locate the declarations of conformity (DOC) for Agilent ScreenTapes and Test-Tapes, certificates of conformity (COC) for TapeStation...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The Automatic Liquid Sampler (ALS) system calibration process aligns the sample tray with the injector turret position to enable vial transfers without incident.
Calibration...