Good day . i have another issue to my 8890. after replacing the fused silica in transfer line. tha air flow in FID is suddenly shutting down. then i try the detector diagnostic in the system it said test failed and need to replace the jet.
after replacing…
Hello,
I am currently developing a residual solvent analysis method by Gas chromatography equipped with a flame ionization detector. My sample is an API with a phosphate salt attached. One of the residual solvents of interest is triethylamine. When…
Hello,
this look like your plasma is not align with the cones. For the EM to failed it's difficult. You have to check for noise when it's doing it and if the counts are low when it's using mass 80. You can try to tune EM with mass 37 if you know where…
8/7/19
Hello,
I have had a fair amount of success with posted questions in this forum, so here is another one. I am interested in knowing more about whether the flame ionization detector I have equipped on my HP/Agilent 6890 GC is the correct detector…
Try to ignite the plasma, without fixing the shield plate. Due to poor quality of argon gas or leak on gas line, reflected power will be above the limit and prevent the plasma sustain. Sometimes, the plasma sensor fiber optics tip is damaged, needs to…
When I need information about detectors I use the following books:
Raymond P. W. Scott "Chromatographic Detectors - Design, Function, and Operation", Chromatographic Science Series Volume 73, Marcel Dekker, New York (1996). ISBN 0-8247-9779-5.
Raymond…
We have a lot of 1260s and 1290s in our lab, and as part of our sustainability initiatives are looking for ways to reduce our energy usage. Currently, all the instruments are left on (standby), and most of them also have the lamps on when not in use.…
Hi Guys,
I have a GC that does not seperate natural gas(maily C1 and C2 with small traces of C3+), it comes as almost one peak, and for condensate (C3+) it seperates C6+, and does not seperate C3÷C5,
I Have,
1: Readjusted the split ratio Many Many…
Hello Inês,
Typically we use the Performance report as a general health report of the instrument. Changing plasma parameters may cause the test to fail, unless you correct the limits. Moving the sample depth will decrease sensitivity and can increase…
Hello
I'm trying to setup report to have values in column "PASS/FAIL" green or red depends on result.
Can I do it as conditional formatting for column "PASS/FAIL" to mark FAIL as red based on text?
This column "PASS/FAIL" is custom field and…
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...