Hi
I have one problem with my 5977B.
The tune no finish, the principal problem or error is "Tune action stopped: Gain and offset = 0 and peaks are too narrow".
Link behind 7820A GC Remote Control Panel Revision 1.5.5.0 279 MB (current) on page above appears to lead nowhere (May 24). Grateful if this could be fixed. Thanks and regards
To learn more about each component take a look at the Concepts Guide manual included with your system and also Parts 2, 3, and soon 4 of this Blog post.
user-manual-msd-system-5977-concept-guide-G7077-90036-en-agilent.pdf
user-manual-tq-gc-ms-7000…
I'm curious to know how the voltage was applied to all the parts. I guess the repeller will be positively charged, and the lens are alternating and probably with RF to help focusing? But what about the ion source body? Is it grounded?
Also curious,…
If you have trouble viewing the content in the EQP files referenced above, refer to Part of PDF is blank when viewing in Edge, but not when I open in - Microsoft Community
Hi fgunawan , thanks for your reply. I did try with 100% IPA, but I didn't run the pressure test and leak test. I am new with the software and learning independently. I will try to explore these options.
Hi Linds,
Linds
Welcome to the Community. I think this is an excellent question, and something we all face from time to time. Thanks for asking!
I'm going to assume that you have a split/splitless inlet. A PM for this inlet usually includes a liner…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
You should be able to but best to get customer care in your region to confirm they can advise on both options. The MS40 upgrade is the better option if you can go for it.
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...