The GC counter rolls over at 999,999...but 100,542 is still a lot!
Great drawing, thanks. That setup makes it difficult to figure out pressures/flows. The path of least resistance is all of the 530 pieces unless the methanizer and the connection from…
The idea behind the multiple modes is to keep the flows going through your FID constant. Changing flows will change the flame characteristics and cause the baseline to shift. Some suggestions:
If your column is set to constant flow mode, use "Constant…
Is there a table / document somewhere on what Agilent GC FID flows I should be using for a particular column ? Right now I have a 7890B with a 30m 0.32 column film thickness 0.25. We use it for petroleum / Diesel Range Organic analysis with a ALS injector…
We have a brand new Agilent 6495 LC/TQ system with a MS 120 rough pump. We vented and shut off the instrument for building maintenance over the weekend. On startup today, the rough pump receives power (the lights turn on) but eventually fails to engage…
Greetings Agilent Community,
Some MassHunter 10 difficulty. I am using the same Quant method that I have used multiple times in the past to process data. This time, however, I am experiencing an error while building my calibration curve. In the Methods…
I recently installed MassHunter Workstation B.03.01 SP2 on my PC to look over some old data that was obtained on a 6540 LC Q-TOF MS system. The instrument hasn't been used for a while now, and my lab no longer has the original computer. We just had this…
Hi,
We currently have as GC/MS/FID using Masshunter and need to print the FID traces as a pdf scaling the y-axis to zoom in on the minor peaks showing %Area values. Is this possible within any masshunter software? I've managed to get a report showing…
Andy G. had the excellent suggestion to decrease draw speed and wait time, since we are working with methanol extract. So we halved the draw speed from 100ul/min to 50ul/min and increased the wait time from 2 to 3 seconds. For now, this seems to have…
I'm not experienced in FID so I'm not sure what normal bleed looks like. So yes I would trim the column and check for leaks first then a new column. Can you look back at older runs when this column was installed to see what the bleed looks like to compare…
Thank you for your response. I really appreciate your help. I realized I didn't provide clear information about the experimental conditions. Here are the specific conditions:
Inlet temperature: 250°C
Column oven temperature: 150°C (isothermal) …
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...