I am using Agilent 8890. I am trying to set the standard for my GC-FID, I am injecting 5mL of methane gas standard with a gas-tight syringe through a switching valve which is set up to the left of my GC. However, I am getting different peaks and areas…
Hello pchinolla ,
If you are referring to B.08.00 Qual Navigator then I'm not able to find a way to label the TIC peaks with the associated compound information. You can export the Compound table from the Workflows view, but that would not contain the…
Do you know about the maelstrom of molecules, atoms, ions, and electrons that are going on inside a GC/MS Electron Ionization ion source?
The molecules streaming out of the end of the column in molecular flow come out at approximately the speed of sound…
The Digest of upcoming webinars has been updated as of March 28.
Check Out:
Back to Basics - IN PERSON - Various Dates
Key Considerations for Dissolution Software and Compliance on May 23
Use of LC-MS/MS Technique for Quantitative Analysis of…
Hi Fury,
Are you using Cary WinUV with the CFR Package which uses CRM? There should be someone who has qualified your system and would also have access. You can also, reinstall the software since there isn't that much to the initial setup if you haven…
Locking does not appear to be designed to lock specific methods as it is to lock the app to prevent say Scan or Kinetics to be used by a second account while the first person is using it.
This Information Applies To: Agilent G1312X and G7112X binary pumps.
Issue:
A blockage before the pressure sensor, e.g. in a pump head, will not give a high pressure or overpressure system error. Instead, the pump may show one of various error messages...
This Information Applies To: Agilent 1100, 1200, 1260 LC Pumps.
Issue:
The following procedure allows the cleaning of residue from the pump's check valves, often caused by polymerization of aged acetonitrile or salt-based solutions that may prevent...
This Information Applies To: Agilent LC Systems
Issue
After analyzing dirty or concentrated samples, some sample compounds may retain in the column and other parts of the HPLC system. If the column re-equilibration after each run is not enough to...
This Information Applies To: Agilent G7167A/B Multisampler.
Issue:
Required when:
The needle is visibly damaged.
Leaks or blockages in the vialsampler are observed, especially between the needle and needle seat.
The limit for the needle...
This Information Applies To: Agilent Autosampler modules G1367A, G1367B, G1367C, and G1367D.
Issue:
The removal and installation of the needle assembly in these older autosampler modules can be tricky and may require patience and the correct technique...
This Information Applies To: All standard analytical scale Agilent 1100/1200/1260/1290 Infinity / Infinity II LC system configurations: Single Pump (Isocratic, Quaternary, or Binary) with Manual Purge Valve. Does not apply to systems with Agilent G7167A...
This Information Applies To: All Agilent LC modules (except hosted modules).
Issue:
When a module does not initialize correctly or it is not recognized by the software, it is recommended to call our Remote Support Representatives to troubleshoot...
This Information Applies To: All Agilent LC pump modules with MCGV installed (quaternary pumps)
Issue:
Shifting retention times: The composition of the mobile phase in liquid chromatography directly influences retention times. If any of the channels...
This Information Applies To: All Agilent liquid chromatography instruments, Lab Advisor
Issue:
The error message 'Could not open channel RD' pops up when performing diagnostic tests in Lab Advisor. Retrying the test is not helping.
Resolution...
This Information Applies To: Agilent Lab Advisor Software for any Agilent LC System.
Issue:
To successfully troubleshoot an Agilent LC system or module, the System Report is an essential resource. Agilent Support representatives may ask you to provide...