Hello everyone, I would like you to help me with a genesys 30 spectrophotometer, I have a problem that says: * Zero-Order search failed
psdt: I have already changed the focus for a halogen one but it only reads from 500 nm but at 325nm it does not read…
Hi. I am having more issues with my ancient 1100 stack. I am getting an EMPV initialization failed error. As I have done some other research it says that the bar should be around 20 bar and then you can do x, y, and z to fix it. However my bar is less…
I'm trying to use the DA Reprocessor (B.08.00) to process TOF data as a batch on a Windows workstation. If there are too many features, the DA Reprocessor stops with the following error in the log: Failed to run worklist Qual: The Operation has time out…
Hi all,
New to the forum, and having a few issues with our analytical 1260 HPLC. Main problem currently is an intermittent error on the auto sampler when trying to inject samples, it doesn’t happen necessarily at the first injection in each sequence…
Which voltage test point? The sideboard is permanently damaged if the cables are connected to it while the power is on. Did that happen?
Notice in your picture above that the HED is set to On.
If the HED power supply is not functioning properly…
Have you checked that your stock standards are not contaminated and tried a second source of SIC. Do you run He in addition to nogas and does it only fail for nogas but pass in He?
I've also seen Sb stick around in the tubing, autosampler probe, and…
That's interesting. I wonder if there are any differences to be expected between a 6890N and a 7890 GC when using Chemstation on the 6890N and Openlab 2.3 on the 7890 with FID? Also, would there be any differences in the signal to noise and dynamic range…
Hello, How often does your reference amount for the compounds change? If it never changes or changes on an infrequent basis I would suggest using a constants file in custom calculator. Also we have seen syntax issues with expressions in IR when using…
Agilent 1200 Series Analytical Fraction Collectors_ Continues to FAIL initialization, also error code 3833 and error message needle too long, too short or missing. please Advise
I have the headspace autosampler 7697A attached to a GC 7890A. I have two issues. the first is a growling noise when the gripper moves in the downward motion. Not the entire way just the middle third. I am guessing a service call will need to be made…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...