The GC Calculators and Method Translation Software (MTS) is available for download from Agilent.com . The package includes:
The Vapor Volume Calculator . It can be used to determine the expansion volume of a GC sample solvent at a given inlet temperature…
Thank you for your advice. Unfortunally not only EM test failed but several others as well. we tried to run it last,first, and even not to run it at all
Hi, Here's a screenshot of the system suit, there is no blank subtraction The analyst said he has used the same processing method for a different run with no issues the only difference being that for those runs the MS setting was the same time as the…
The basic tools I would recommend to have for GC maintenance:
Ceramic column cutter
1/4" wrench (column nuts)
7/16" wrench (gas fittings at back of GC)
1/2" wrench (replace gold seal on S/SL inlet)
Torx 20 driver (removing FID collector assembly…
Agilent GC 7890A, FID, Split Liner. I'm setting up the column to do Hexane injection testing. It was set up this way previously but the program had been deleted and the column removed before I started here. Front Detector/Column which is below baseline…
Hello and Help!
My GC-FID's inlet pressure stays at 0.7 psi and does not reach the setpoint of 10 psi. Makeup gas reaches the 25 psi setting. Liner and septa are fine. I unscrewed the inlet column nut and placed my finger at the bottom of the inlet…
Hello,
My laboratory runs a multilevel calibration with internal standards on a headspace-GC-FID. Our sequence is set up to replace each level of the curve after each calibrator is analyzed and then calculate the concentration of the analyte with the…
I'm going to be calibrating for ethanol on my HS-GC-FID 6890, but I'm having discrepancies between two standards. The standard that I will be calibrating with (Restek's Residual Solvents #1 34105) is 3000ug/mL in N,N-Dimethylacetamide. I'm verifying the…
When you say that there are no signs of a leak, have you run a pump leak rate test using Agilent Lab Advisor? If not, I would suggest testing this. If you're unlucky enough for your peak to elute just at the point when the outlet ball valve fails to close…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...