It is a capillary, USP 401 The gas chromatograph is equipped with a flame-ionization detector, maintained at a temperature of about 260°, a splitless injection system, and a 0.53-mm × 30-m fused-silica capillary column bonded with a 1.0-µm layer of phase…
Hello SimonHarries ,
The only time I have heard an FID trying to re-light itself is when the baseline of the FID dropped below the Lit Offset value.
What is your baseline at (in pA) when the FID is lit, but not running sample? And what is your lit…
User could not tune and was getting missing .xml errors. This error was observed in MassHunter Acquisition software B.07.00 on a GC QQQ but may be relevant in other revisions as well. Error in auto tuning! Missing XML file or invalid contents. Failed…
Hello! I followed this tutorial part D Linked Dual GC Signals 1 aliquot /cfs-file/__key/communityserver-discussions-components-files/152/0020.DualTow7890EnvMH.pdf to sample 1 aliquot through both the front and back autosamplers, both columns, to both…
Hello howard_sanford ,
I tried clearing the preferences for IDBrowser, and it did work when I used the old PCDL, but the "m/z" column in ID Browser did not show anything. So, I did it again and for the second time, the m/z of features showed up, but…
I got a data sheet for my Agilent 7890 FID detector. The stated linear range is 10x7. This range I think should mean that from 1% down to 0.1 ppM the detector is linear for Tridecane. I figure concentration-wise in splitless mode - that works out to be…
Column: HP-PLOT/Q+PT 30M +5M Duraguard (2.5M on either end) 0.530 mm megabore, 40Micro film Primary components residual EO and PO in various acceptor chemistries. Separate STDs for each, both are showing area decline, on FID, recently switched out flame…
Hello, We are using Agilent 7890B GC/FID with Headspace sampler. There is a problem in FID unit of the system. In FID parameters, Temp is 220 C, H2 fuel flow is 30 mL/min, Makeup flow (N2) is 25 mL/min, He flow 1 mL/min. These are setpoints and actuals…
In my experience, usually when a method fails to download to a 7820A GC it means that one of the zones on the GC is in a faulted state. This does not always get reported in the instrument actuals in ChemStation, so the best way to double-check this is…
Hi chemist85 , I'd like to inform you that our instrument problem was solved, and yes it caused by the broken UPS, the output voltage is dropped to 160 volts when igniting the plasma, and also the voltage was not stable at all and unfortunately, it also…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...