Thanks a lot.
Also I found that not all parameters (column width, labels) can't be changed in report designer. I changed them in xml template manually. Is there any description of functions and variables to change some report layout?
In the earlier 2 posts, I have discussed about 1. The merits of automated sampling and 2. Validation of automated dissolution system . Thank you for giving our team warm response for these blogs. We received many queries regarding automated sampling on…
Hi Lisandro,
if your analysis looks fine, go for it. The mentioned increase in off-mass background can affect your signals (not predictable) on other masses, as it is electrical noise.
BR Chris
Hi,
rinsing with a higher concentration of HNO3 sounds like a plan
you could try to sonicate the T-Piece where the istd is connected. Often this is a source for contamination. Anyway the Pb is not a problem in this low concentration. And your main…
That video is a bit hard to see. There's no visual evidence of overheating nor staining on the rest of the analyzer/quad radiator. The factory gold is not a separate applied foil. That needs further investigation. I would recommend contacting Agilent…
Hello,
I am not entirely clear on what you are doing as well. Below is an example of how I would do a % recovery from an existing standard injection in the result set. The calculation would pull the theoretical value (Compund_CalibrationAmount) from…
Hi JONHY , thanks for your question.
I’ve used an online tool to translate your post. English is the official language of the Agilent Community, and the platform does not support translating a post from local language to English. You can view pages…
Hello,
I think there are other posts where I go over this in more detail. If you want to do a recovery or check calculation for more than one compound and it is not a reinjection of a standard level or the standards are not in the results set, the…
Hello,
Yes, that will not work. You need to test the length of the name as I said in the previous response. See the example below the unknowns have a low value of 1.56.
if(LEN(Compound_Name)>0, getconstant(“Relative response factor”),0.98)
…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...