Wondering if anyone has experience detecting acetic acid and formic acid using GC-FID HSS. I am trying to develop a method based on the limits described in USP <467> of 5000 ug/mL of each of the two solvents, but having a hard time seeing any peaks.
Hello,
we are using a G1312B binary pump (1260 Infinity) and had the error message: Fan Failed
After acknowledging the error message I can turn on the module as usual and it is working quite fine.
Nonetheless, I am not sure whether the fan is working…
Hi, I know this is an old thread, but I am having a very similar issue. I am wondering how did you know to replace the interconnect spring rod? How did you know this was the issue, and that it was not instead an issue with the FID board or the electrometer…
I have a 6890N GC with dual FID. The back column has a much higher flow rate than the front column. The two columns are identical and the setup for inlet, column and detector are identical. I have also swapped the EPC's between the two detectors. Seems…
Hello ljones031 ,
I would suggest copying the installation files to a folder on the local hard drive and then disconnecting any external drives before attempting installation. Most MassHunter programs will try to install to a D: drive it if is found…
I am getting message "draw command failed, EE34205" while running batch in G7129B infinity 2 autosampler. I have tried replacing transport assembly, but error is same. I have used another module G7129A Infinity autosampler with this LC, but same error…
Hello,
Thank you for the response. I created MH_meida folder in C drive and also enabled .NET 3,5. But I received error message again after trying to install qual 10.0. Any suggestions would be much appreciated. Thank you.
here is the error log…
We don't know what is in your water samples, but on a CP-Wax 57 CB benzene and isopropanol are eluting very close to ethanol, just in front of it.
You can find examples of applications of alcoholic beverages on Wax 57 (all types) in Scanview ( (+) Software…
Hello mckenzie.stevens ,
Did this error occur when attempting to work with the FID data? I've not seen this exact error, but it is possible to receive similar errors when having a spectrum tool selected and trying to work with non-MS data. If you then…
Hi Ran,
Thank you for contacting us and I am sorry to hear that you are observing this issue. Based on the symptoms observed (low signal intensity causing the lower markers not to be detected combined with the autofocus failure) may indicate hardware…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...