Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
I'm running a GC(7890A) / MS(5975C) with MassHunter Acquisition software. I automate much of my data analysis in Python by exporting the GC signal (FID) to .csv, and then exporting the MS signal using 'Export 3-D Data...' in MSD Productivity Chemstation…
Hello MikeL ,
Just wanted to post what we discussed during your call with the support center so if anyone else sees a similar problem they will have some things to try.
There can be issues with copying and pasting fairly large amounts of information…
Recently, we connected the column (CP7429) to TCD and FID using a Y splitter. However, there is no signal response on both TCD and FID after manually injection of the calibration gas (containing H2, CO, CH4, C2H4, C2H6 in CO2). The carrier gas is Ar.…
i had faced this troubleshooting before
it is probably a software problem.
first close masshunter and double click ( remove masshunter process)
open the soft again and try to create another method with same parameters it should work
also try to…
When performing the Eukariote Total RNA test on the same chip we had some samples with very degraded RNA and one sample with what seems like good quality RNA but the software failed to give a RIN value for that sample. Is there a way to still measure…
Dear Colleagues, apologizing for frequently wondering but I first faced this problem. GC produces a signal without turning on the FID Detector!? Please look at the attached photo. After turning on the detector and then conditioning the column while the…
For many FID methods, 10-20 Hz data rate is sufficient unless you're doing a fast method of some sort. You need enough data points to define the peak correctly and not get any spectral tilt. Typically 15-20 points across the peak is enough.
Hello AGILENT family,
i have a few questions on the analysis of Pb in blood samples.
am failing to get the right concentrations of the QC sample 8ppb instead it’s reading 0.08 ppb and at the same time it’s also showing overange (0.08o) even when my…
I am a user of an Agilent 7900 ICP-MS. It has been working fine since last month, but today (Oct 13, 2022) the software was not able to connect to the instrument. When I try to connect the MassHunter software to the ICPMS by going to settings > mainframe…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...