Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
Hello LC92 ,
Did you run the installer as an Administrator? That might cause issues like this.
Another thing to try is running the Software Verification Tool found in the Start menu under Agilent Technologies. See if there are any missing files. You…
Learn about how to check and extend the lifetime of peristaltic pump tubing; prevent and remove nebulizer blockages; clean the nebulizer and improve precision and reduce memory effects with spray chamber cleaning.
Preventative maintenance is crucial…
Learn more about accurate ICP-MS standard preparation, sample introduction, diagnosis of sample introduction issues, and preventive ICP-MS maintenance guidelines. In this video we provide simple steps to improve sensitivity and accuracy, precision, and…
If you have data associated with a worksheet you cannot make modifications to it. Depending on your software version, you will need to either do "Save As" and give it another name, or create a new worksheet from template. Then the new worksheet will not…
Hello. You have to adjust Nitrogen pressure to get the blue bar inside green area. Pressure regulator is located on the right side of the 4107. It should be ~ 600kPa.
Hello mipastor,
Thank you for your response. I think we do have problem with the MS2 heater. Agilent customer support hinted that it might be sensor problem or the board so service engineer will have to take a look.
The Digest of upcoming webinars has been updated as of April 23.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...