Hello:
Please contact your local Agilent office with the serial number of the temperature control box and the instrument. Repair may be an option, otherwise Agilent can quote you on a new one.
Berst regards,
Mike
Hello,
Thank you for reaching out with your VWorks question.
In general, you can either perform this as a series of tasks as you have already done or make use of loops and scripting to condense the protocol. As you noted, using loops will continuously…
On Thursday, June 6, we presented the third installment of our GC Live series. Our speakers discussed how the new single-channel 8850 GC can help labs maximize productivity, efficiency, and uptime.
Watch the recording at your convenience using the link…
Thank you for contacting Cell Analysis Technical Support. This will depend on your instrument type. See this link as well as the screenshot below. Keep in mind that these ranges are pre-normalization.
For Cell Mito stress test, Seahorse Cell Mito Stress Test Kit, the recommended working concentrations are 1.5 µM for Oligomycin and 0.5 µM for Rot/AA. The FCCP concentration needs to be optimized (0.5 µM-2 µM). The optimal final compound concentration…
In general, the %CV across a group and from plate to plate should both be < 20%. Higher CVs in this case was due to edge effect on outside of the plate.
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...