You should be able to but best to get customer care in your region to confirm they can advise on both options. The MS40 upgrade is the better option if you can go for it.
It depends on what you have installed. There is an upgrade kit. The old-style chambers are no longer available. You may want to contact your local service group.
Also, if too costly maybe upgrade to a newer degasser.
5067-5387 vacuum chamber replacement…
Here's what's new in the latest release of MassHunter BioConfirm Software.
New peptide ECD fragmentation MS/MS capabilities with c and z fragment ion data analysis
Expanded capabilities for linear synthetic peptide analysis
Modernized interface…
The senTorr controller used to have a RS232 Serial communication add-on kit, but it was obsoleted as well as the senTorr gauge controller. The XGS600 is the current Agilent Gauge controller for Ion Gauges. Vacuum Multi-Gauge Controller ATM-XHV, XGS-600…
Generally, you would start method development with what you find in the USP and/or FDA Dissolution Method Databases for volume, media, RPM, etc. requirements. The FDA method database points you to: Dissolution Testing and Acceptance Criteria for Immediate…
That turbo controller and the 300HT turbo pump are obsolete. The RS232 communication kit referenced in the controller manual is also no longer sold by Agilent (previously Varian).
The current model turbo pump of that size is the 305FS turbo. Turbo Pumps…
Hello Kart995,
What vintage is your Bravo, could you please share serial number?
which .dev file are you trying to load did it work on this computer before?
Does the error say "Device type Bravo does not exist"
Are you able to initialize the Bravo…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...