Is the MS still pumped down and ready to go? Do you have -- Use the MS -- checked in the method? If the column is connected to the FID and the MS is not running you'll need to uncheck that and save the method, hopefully with a new name like No_MS_FID_Only_28Feb2023…
Hello, is it possible to operate a HP 5890 II with 7673 in standalone mode completely without computer/integrator?
I'm trying to set up a GC taken from a former GC-MS system working with a PC over GPIB. It should now work as GC-FID together with the…
I am getting message "draw command failed, EE34205" while running batch in G7129B infinity 2 autosampler. I have tried replacing transport assembly, but error is same. I have used another module G7129A Infinity autosampler with this LC, but same error…
Hi Ran,
Thank you for contacting us and I am sorry to hear that you are observing this issue. Based on the symptoms observed (low signal intensity causing the lower markers not to be detected combined with the autofocus failure) may indicate hardware…
Hi,
I removed Heater/sensor assy from Back channel and put in front channel FID and again reconfigure FID.
Upto now, it's working.
Means Heater/sensor assy was faulty.
But still, one thing I am unable to understand that Fid block was heating earlier…
The computer suffered a firmware downgrade and now it has firmware A.1.08 which we need to update to maybe A.1.16 or A.1.12 but the pc has windows XP. (currently it is giving us an error "AUX HEATER 2 FAULT ") It is a 7890A GC (FID) with MS 5975C that…
Thank you for your response Today when you open the GC we noted the increase returned valid but not connected and the Remote LED off we tried to configuration instrument but a message appears(failed to connect to 6890 at 100.100.100.101)but the GC IP…
We have a baseline that gives a sinusoidal wave that starts about 16 minutes. We are using an Agilent 6850 GC with a split/splitless injector and an FID. The inlet is interfaced to a 7679A HS. The baseline is good up until 15.5 minutes then it starts…
Hi, Howard Sanford
Thank you for your replay. The version of MassHunter (MH) Data Acquisition and quantitative analysis programs software is B.07.00.
Unfortunately, there isn’t any error code for this problem. But a window with “The head of file could…
This file contains a list of 86 commonly used consumables and parts for 8860 and 8890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
This Information Applies To: Agilent Atomic Absorption Spectroscopy Systems (240/280 Series Flame AA and 240/280Z/Zeeman/GTA 120 Graphite Furnace)
Issue:
This article includes recommended maintenance procedures to be performed daily, weekly or annually...
This Information Applies To: Agilent SpectrAA Software, Agilent 240/280 Flame Atomic Absorption Systems, 240/280 Zeeman Graphite Furnace Systems
Issue:
How to Reset Lamp Usage Counters or Add a New Lamp in SpectrAA
Caution : All physical...
This Information Applies To: Agilent GTA 120, Agilent 240Z AA Spectrometer, Agilent 280Z AA Spectrometer, Agilent 240FS/GTA120/PSD120/UltrAA System
Issue:
It is important to align the sample probe of the Programmable Sampler Dispenser (PSD) 120...
This Information Applies To: Agilent Flame AA Systems: e.g., 55B, 240FS, 280FS
Issue:
The Flame AA burner and burner components require regular cleaning to maintain system performance. Components include the burner, nebulizer, and spray chamber...
This Information Applies To: Agilent Flame Atomic Absorption (AA) Spectrometers (50/55/240/280 AA)
Issue:
How to clean a blocked nebulizer of a Flame AA, which may be causing low sensitivity or a sample uptake rate below 5 ml/min.
Steps to follow...
This Information Applies To: Agilent Graphite Furnace Systems (PSD 120/GTA 120/240Z AA/280Z AA)
Issue
Maintenance procedure for replacing the syringe and plunger of the PSD 120 sample dispenser for the Agilent GTA and Zeeman Graphite Furnace Systems...
This Information Applies To: Agilent AA (AA240, AA280) with Graphite Furnace Accessory (GTA)
Issue:
The Programmable Sample Dispenser (PSD) requires the sampling probe to be accurately aligned before the PSD can be used.
The PSD enables the...
This Information Applies To: All Agilent AA systems: 55B, 240FS, 280FS, 240Z, 280Z
Issue:
Optimizing the position of the lamp maximizes amount of light from the lamp passing through the optics to the detector, improving the signal-to-noise and the...
This Information Applies To: Agilent VGA 77, AA, VGA 77P, ICP
Issue:
The Agilent Vapor Generation Accessories VGA 77 and VGA 77P use high concentrations acids. The system needs to be thoroughly cleaned after each use.
The Vapor Generation Accessory...
This Information Applies To: All Agilent Atomic Absorption Spectrometry Systems (AA50, AA55, AA240, AA280)
Issue: This article describes when and how to clean an AA burner.
Background
For optimum and safe performance, burners (see Figure 1 ...