When using the Microlab PC SW in conjunction with the 21CFR11 software, the PUBLIC database must be part of the data PATH. It needs to be added to the GROUP (easiest to do it here), the PROJECT or the USER. Otherwise the error described will always be…
Hello:
Please contact your local Agilent office with the serial number of the temperature control box and the instrument. Repair may be an option, otherwise Agilent can quote you on a new one.
Berst regards,
Mike
Hello,
Thank you for reaching out with your VWorks question.
In general, you can either perform this as a series of tasks as you have already done or make use of loops and scripting to condense the protocol. As you noted, using loops will continuously…
On Thursday, June 6, we presented the third installment of our GC Live series. Our speakers discussed how the new single-channel 8850 GC can help labs maximize productivity, efficiency, and uptime.
Watch the recording at your convenience using the link…
Thank you for contacting Cell Analysis Technical Support. This will depend on your instrument type. See this link as well as the screenshot below. Keep in mind that these ranges are pre-normalization.
For Cell Mito stress test, Seahorse Cell Mito Stress Test Kit, the recommended working concentrations are 1.5 µM for Oligomycin and 0.5 µM for Rot/AA. The FCCP concentration needs to be optimized (0.5 µM-2 µM). The optimal final compound concentration…
In general, the %CV across a group and from plate to plate should both be < 20%. Higher CVs in this case was due to edge effect on outside of the plate.
This Information Applies To: Agilent Atomic Absorption Spectroscopy Systems (240/280 Series Flame AA and 240/280Z/Zeeman/GTA 120 Graphite Furnace)
Issue:
This article includes recommended maintenance procedures to be performed daily, weekly or annually...
This Information Applies To: Agilent SpectrAA Software, Agilent 240/280 Flame Atomic Absorption Systems, 240/280 Zeeman Graphite Furnace Systems
Issue:
How to Reset Lamp Usage Counters or Add a New Lamp in SpectrAA
Caution : All physical...
This Information Applies To: Agilent GTA 120, Agilent 240Z AA Spectrometer, Agilent 280Z AA Spectrometer, Agilent 240FS/GTA120/PSD120/UltrAA System
Issue:
It is important to align the sample probe of the Programmable Sampler Dispenser (PSD) 120...
This Information Applies To: Agilent Flame AA Systems: e.g., 55B, 240FS, 280FS
Issue:
The Flame AA burner and burner components require regular cleaning to maintain system performance. Components include the burner, nebulizer, and spray chamber...
This Information Applies To: Agilent Flame Atomic Absorption (AA) Spectrometers (50/55/240/280 AA)
Issue:
How to clean a blocked nebulizer of a Flame AA, which may be causing low sensitivity or a sample uptake rate below 5 ml/min.
Steps to follow...
This Information Applies To: Agilent Graphite Furnace Systems (PSD 120/GTA 120/240Z AA/280Z AA)
Issue
Maintenance procedure for replacing the syringe and plunger of the PSD 120 sample dispenser for the Agilent GTA and Zeeman Graphite Furnace Systems...
This Information Applies To: Agilent AA (AA240, AA280) with Graphite Furnace Accessory (GTA)
Issue:
The Programmable Sample Dispenser (PSD) requires the sampling probe to be accurately aligned before the PSD can be used.
The PSD enables the...
This Information Applies To: All Agilent AA systems: 55B, 240FS, 280FS, 240Z, 280Z
Issue:
Optimizing the position of the lamp maximizes amount of light from the lamp passing through the optics to the detector, improving the signal-to-noise and the...
This Information Applies To: Agilent VGA 77, AA, VGA 77P, ICP
Issue:
The Agilent Vapor Generation Accessories VGA 77 and VGA 77P use high concentrations acids. The system needs to be thoroughly cleaned after each use.
The Vapor Generation Accessory...
This Information Applies To: All Agilent Atomic Absorption Spectrometry Systems (AA50, AA55, AA240, AA280)
Issue: This article describes when and how to clean an AA burner.
Background
For optimum and safe performance, burners (see Figure 1 ...