It's often difficult to tell when to change filaments. It depends on use, samples, gases, gas cleanliness, and number of tunes. Certainly inspect them when the source is out for cleaning. If the wire is smooth and clean it's fine to reinstall. If the…
Hello jeremy_lai ,
There are details about adding additional qualifiers and ISTD information in this discussion.
(+) Qualifiers in Report Builder - Forum - Mass Spectrometry Software - Agilent Community
Here are the main points from that discussion…
Hello Darija ,
You may want to investigate using the blank offset option for the calibration curve. Details can be found in this discussion.
(+) "Blank Offset" in MH Quantitative Software - Forum - Mass Spectrometry Software - Agilent Community
…
All our packed columns come already with a frit on inlet and outlet sides. Their porosity is smaller than any glass wool could be. If you still want to have a liner, please use our GC Liner Selector | Agilent
Regards,
Norbert
You've got column in your column. A bad cut usually just results in tailing. Doesn't sound like the rear was touched, recut the inlet side and try again.
Hello,
No, you cannot create custom sample types in CDS. You can use an existing field like sample label to mark specific injections if you need more delineation than the sample types can provide.
Marty
Hello,
To check if you have access to a core facility in iLab, log into your iLab account and navigate to the core facility's page. If you are not prompted to request access and can view sections such as “About our Core,” “Request Services,” or “Schedule…
Hi Sabbas,
if you have measured a batch and click the print button, all method parameters are shown in the report. I’m not sure if you can print the report of method solely without having measured a sample. I would in that case just measure a blank…
Here a list of suggestions to try if encountering an error 155 on ELSD:
Make sure driver is at least A.01.07 DU1. Along with that, make sure the firmware and software is compatible with the driver.
Consider lowering the data rate (40 Hz if this…
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software version B.02.08 or later
Issue
When printing a report to PDF or HTML with the 2100 Expert software, the error "Failed to Generate Report" appears.
Background
This error...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue
Resetting upper or lower markers from their automatically assigned settings in the Agilent 2100 Expert software.
Background
The Agilent 2100 Expert software...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert Software
Issue
Samples with a broad signal such as NGS smears should be analyzed by setting up a region. Analyzing a region is also termed smear analysis.
Steps to Follow...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RIN NA, Error 4501, RNA 6000 Nano kit (p/n 5067–1511 ), RNA 6000 Pico kit (p/n 5067–1513 )
Issue:
The RIN is not displayed in the software or shows as NA. If the RIN is NA, the...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RNA 6000 Nano kit (p/n 5067-1511), RNA 6000 Pico kit (p/n 5067-1513)
Issue:
Which assay should be selected in the Agilent 2100 Expert software when running yeast total RNA samples...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software, RNA assay, DNA assay, Protein assay
Issue:
The X-axis description toggle icon in the Agilent 2100 Expert software toolbar ( Figure 1 ) does not change the X-axis from time...