I have a 5890 GC running ASTM D2887, simulated distillation. It is equipped with a FID and recently we noticed the FID won't light. Flows are good and gases are good. Looking at the setpoint/actual reading, it states it is at the correct temperature …
I appreciate your answering my post!
I tried launching in the Control Panel, with the correct project selected. I also tried to launch MH12.1 using a desktop shortcut made for that project.
I'm sorry, I'm not sure what ESW/FW refers to, could you…
Adding to this post,
I've tried creating a virtual instrument to check if is a problem with the hplc, Aquisition still is not opening for the virtual device.
the acquisition logo stops at initializing modules, turns black and then crashes.
Hello DET ,
Sorry for the late response on this.
What sort of spiking do you see usually? What is the output of the FID, in pA?
Are you using any UPS systems, or are the GCs plugged directly into the wall?
Our customer got an error, "Failed to connect to an IPC Port: The system cannot find the file specified." from MassHunter.
Do you know any cause of this message? There was no record of this message in the diagnostic log files.
during installation of NEW FLD Detector it started to show error Excitation Motor didn't find its position then gives error Excitation motor has failed and last error it still showing up is Exciation endcoder index failed to calculate so what do you think…
I am getting an error on our Agilent 1290/6420 LC-MS/MS. I start a run and the first injection is successful, then when it goes to the second injection, it errors and says "failed switching to main pass" and shuts down. From my reading, this is a failure…
I have just received the Agilent Cary 60 UV-Vis photospectrometer and while following the steps to install the software i receive and error pop up which says "failed to register Class not registered" this occurs no matter what software i try apart from…
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...
Turn On the GC/MS Interface and Oven Using OpenLab CDS
Multiple Results
This Information Applies To: Agilent GC/MS instruments controlled by OpenLab CDS software
Issue
Turning on the GC/MS interface heater and Oven using OpenLab CDS software.
Steps to Follow
From the Home tab, click Method > Instrument Setup...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900)
Issue
The signal monitor function in MassHunter can help with troubleshooting low sensitivity, carry over, contamination, or high background. It can also be used to optimize...
This Information Applies To: Agilent UV detectors (Variable Wavelength Detectors, Multiple Wavelength Detectors, and Diode Array Detectors)
Issue
Checking accumulated hours on the UV lamp.
Steps to Follow
There are four ways to check the accumulated...
This Information Applies To: Agilent 7700/7800/7850/7900/8800/8900 ICP-MS
Issue:
Poor internal standard (ISTD) mixing can cause high relative standard deviation (RSD).
The recommendations in this article are applicable if:
It takes a long...
This Information Applies To: Parallel capillary electrophoresis platforms, 5200/5300/5400 Fragment Analyzer, ZAG DNA Analyzer, Femto Pulse, Oligo Pro II
Issue:
Disposing used capillary arrays
Resolution:
Arrays can be discarded in regular...
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, ProSize software, DNF-471 RNA kit, DNF-472 HS RNA kit
Issue:
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE...