Here is a "best of" collection of links to manuals, tools, and other resources for Agilent Cell Analysis products. For other instruments refer to Collection of Support Resources .
Collection of Cell Analysis Resources
See also the new Cell…
Thanks for reply.
I am not using any multi wash but injector is a dual injector model. When any parameter changes in method both injectors are flushed. The time taken in doing so is that much that system generates error.
No I haven't. But I think that is the only solution. Perhaps there are somehow misalignment making it not robust and the needle fail to go in the vial and abort the run randomly. . I will do the auto-reference and I will wait and see how frequent the…
As title states.
Instrument: #1 shows "GCMS9"
Instrument #2: should show "GC16"
However on the quant report, only Instrument #1 is accurate, the quant reports on #2 read HP G1530A
I've checked msdchem.ini and InstName is defined properly…
Hello,
Did you apply update 06 before upgrade? It´s necessary.
This update 06 fixes this flaw in version 07, after this action you update to version 08.
Regards,
Rafael Pinto
The Cary 60 UV-Vis and its nearly endless supply of accessories
We’ve written before about the many accolades of the powerful yet accessible Cary 60 UV-Vis and its highly flexible software. This instrument’s popularity seemingly knows no bounds and…
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...
Turn On the GC/MS Interface and Oven Using OpenLab CDS
Multiple Results
This Information Applies To: Agilent GC/MS instruments controlled by OpenLab CDS software
Issue
Turning on the GC/MS interface heater and Oven using OpenLab CDS software.
Steps to Follow
From the Home tab, click Method > Instrument Setup...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900)
Issue
The signal monitor function in MassHunter can help with troubleshooting low sensitivity, carry over, contamination, or high background. It can also be used to optimize...
This Information Applies To: Agilent UV detectors (Variable Wavelength Detectors, Multiple Wavelength Detectors, and Diode Array Detectors)
Issue
Checking accumulated hours on the UV lamp.
Steps to Follow
There are four ways to check the accumulated...
This Information Applies To: Agilent 7700/7800/7850/7900/8800/8900 ICP-MS
Issue:
Poor internal standard (ISTD) mixing can cause high relative standard deviation (RSD).
The recommendations in this article are applicable if:
It takes a long...