Thanks for your reply. The syringe O rings are quite old so I will change them. I was able to overcome the issue by using a pulsed split mode on the inlet. Your other points are very helpful info and give me things to investigate.
Browse the help documentation by using the navigation menu or the links below.
Agilent Community Best Practices
Forum Best Practices
How to Post a Question
How to Reply to a Question
How to Attach Files
How to Configure Notifications…
Use the navigation menu to view our help articles.
Customize Your Email & Live Alert Notifications
Subscribe to Areas of the Agilent Community
Turn on or off Email Notifications
Which Electron Ionization Source Part 1 had questions. Which Electron Ionization Source Part 2 had some answers. Now, let’s talk about each source and tuning.
Stainless Steel/Inert vs. Extractor, Atune vs. Etune - The colored lines in the diagrams …
Hello MLGonzalez ,
In place upgrading for quant was only supported starting at Version 12.0. If you have any versions prior to that you must first uninstall quant before attempting to install a different version. If this was Quant 11.0 for TOF/QTOF…
Weird situation.
My 7890A stopped communication with Chemstation B.04.03 SP2 [106] Windows 7. I am getting a module not found error. I was running fine then just stopped after a reboot.
I moved the instrument to an XP laptop running B.04.03 [16…
Hi Evans! I would like to know if you ever figured out what could have caused the error with the oxygen sensor? We just had the same issue in our labs, and have got a new sensor. We are however hesitant to use the instrument again before we we have an…
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...