You might try to modify the monitored wavelength not from the Driver (main screen), but from the Method-Edit Entire Method menu. Go through all the screens and make sure to update the wavelength everywhere where it appears.
Hello,
This is the same as the previous post, but you would change the names in the 2 filters to match the groups names. In the example the groups are Group A and Group B, those would need to be changed to your group names. If you need both calculations…
Hello,
You could do it directly in the table with a conditional aggregator and then display the sum in the bottom table. I assume that is what you might be doing now. You can do this with the CCs below. You calculate the total area and then use that…
No, it is not possible. The units in this case are relative and depend on the differences in optical units, PMT settings, etc. Even if you had two detectors from the same company you still would have to optimize PMT to scale the signal to similar values…
Yes, it is possible if the port on the stator is blocked. You can use a torch and check whether the same bright light comes from port 2 and other ports. You can either try to clean with compressed air or you might need to replace the stator.
I figured out where the problem was. The default RT window size factor of 100 was too small to capture all mass spectra of my compound. I increased it to 400 and now the Qual can properly identify what I was looking for (Diterpenes).
Hello,
Please turn off the SPS4 and inspect the belt Z and check the movement of the Probe up and down. It should move freely up and down without resistance too much. If not, then you need either repair onsite or you order the Z belt for replacement…
This Information Applies To: 2200/4200/4250 TapeStation systems, TapeStation D1000 ScreenTape assay, TapeStation High Sensitivity D1000 ScreenTape assay, TapeStation analysis software
Issue:
A sharp peak appears at the lower end of the NGS library...
This Information Applies To: Agilent Variable Wavelength Detector G1314x and G7114A/B modules.
Issue
As UV deuterium lamps ages, the light intensity decreases, the sensitivity of detection may deteriorate. Replace the lamp when the intensity test...
This Information Applies To: Agilent 6850, 6890, 7820, 7890, 8850, 8860, 8890, Intuvo 9000 GC Systems with a Thermal Conductivity Detector (TCD)
Issue
The TCD temperature, column (carrier), makeup, and reference flow rates need to be optimized to...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...