What should you consider when selecting gases for your new GC or GC/MS system?
Which gases will you be using?
Did you c onfirm that gases available are a supported configuration for installation ?
Gas requirements are specified in Site Preparation…
Hi Carmen,
Visually check your column in signs of contamination of stationary phase. It looks like your column was too old. In that case you could just reverse the column direction, and put for for long term conditioning at room temperature, then condition…
Hello! My multisampler (G7167B: DEBAR00250) has the following error: compressor has error EE 30756,0. According to the manual, this indicates a possible hardware error. I ran a sample cooler function test, which failed, and the result comment is: target…
Hello, I am running residual solvent testing on a product for my company and I am having issues with peak sensitivity. I am running this testing on a 7890/7697 GCHS-FID combo. I am tasked with coming up with a solution to this issue by only adjusting…
Dear colleagues
We have Agilent LCMSD 1260 Infenity /6130Quaderpole. we encountered this error: Install module C:\Chem32\CORE\HPSCIL00.DLL, failed
We want to know the cause and the solution for this error ?
Thanks in advance.
With my best regards…
We are running long term tests with multiple GC analysis, automatically controlled from LabVIEW via ActiveX communication with OpenLab EZChrom. We recently had an event in the EZChrom software creating problems; suddenly midway through the tests, the…
I have proposed system from agilent 7890B to check high purity gases . system consists of TCD , PDHID and FID . me question is do you think that system is complicated and i have risk that if any fault happened the whole system will be down . How to guard…
Good afternoon all. I have a baffling issue with our 6470 LCMS. It passes checktune. I can run autotune is positive mode or in negative mode, but not both together as previously. I get an error message at the end of the autotune process stating "Failed…
Hi Kris, thank you! I tried to upload the screenshot of the version info, but I failed. So I have to type all of them out since I'm not sure which one is useful. Hope it can help!
Agilent OpenLAB Intelligent Reporting A.01.11.138
Agilent OpenLAB CDS…
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
Early Maintenance Feedback is a useful feature on Agilent GC Systems and software that allows a user to monitor the maintenance needed on their GC. This feature allows for users to...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue:
This procedure outlines the steps to view and clear the maintenance warnings on based on Agilent 8890/8860 GCs. You can also follow the onscreen instructions to perform maintenance...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with Agilent MS-40+ rotary vane pump.
Issue
Regular check of the rough pump fluid level in your MS40+ pump as part of regular 6000 LC/MS system maintenance checks.
Steps...
This Information Applies To the Following Products : All Agilent iFunnel and Agilent Jet Stream (AJS) 6400 Series LC/MS triple quadrupole systems, Agilent 6460A/C, 6470A, 6490A, and 6495A/B/C
Issue:
As LC Triple Quadrupole Mass Spectrometers (LC...