This file contains a list of 59 commonly used consumables and parts for 7890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
Hi JF_Fortin ,
As andyg mentions, starting with Qual B.08.00 SP1 and Version 10.0 the handling of data files with only 2D detector data has been improved to automatically open non-MS chromatograms.
In previous versions the message you are seeing is…
Hi,
this is a very nasty mass axis.
Could you please confirm, that you have S-Lenses installed, as they are configured.
Please have a look, through this troubleshooting guide and follow the instructions. Hopefully it will solve your problems, or…
Hello vtpolywood ,
What type of GC do you have, if I may? If it's an 8890 for example there are some Diagnostic tests built-in that you can run on the Cool On Column inlet. Have you recently changed gas tanks (whether carrier, FID fuel, air or makeup…
In MSD Chemstation, you can specify which signal to use for quantification: TIC, Target Ion, or GC Signal (for GC detectors like FID, TCD, etc.) Go to the Calibrate menu and select Edit
Compounds. On the Compound Table Identification tab, look for the…
Hi,
I plan to attempt some SimDist analysis in accordance with D2887 on my agilent GC-FID. I was hoping that I could achieve this without additional software (i.e. just through manual manipulation of the data acquired by Chemstation), but apparently…
ICP-MS MassHunter Version 4.1. I cannot Startup Standard Lens Tune!
The message appears "Failed to add Startup/Hardware tasks to Queue; Enter path for batch folder".
As usual (my Batchs)- everything works.
Hello,
Our Headspace sampler 7697A Leak test failed. Leak test failing at the stage 1 off the Restriction and Pressure Decay Test.
Going from there, the sample probe was replaced as well as the pressurization solenoid valve but without success.
…
Hi everyone.
We have a 8890 Agilent GC with nickel catalyst and FID detector. We would like to use hydrogen as carrier gas, but we don’t know the right flow rates, because the manual is indicating flow rates only for using helium as carrier gas.
For…
This Information Applies To: 1100, 1200 and 1260 Infinity I and 1260 Infinity II LC Pumps (Excluding preparative pumps with electromagnetic purge valve (EMPV): G1361A. Not applicable to any of the 1290 Infinity II modules with automatic purge valve: G4220X...
This Information Applies To: Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules
Issue:
Removing and re-installing Visible and UV lamps in Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules.
Both the visible and UV lamps are consumable...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pumps.
Issue:
Removal of the pump head from the pump metering drive for maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Module.
Steps...
This Information Applies To: All Agilent 1260 Infinity Binary, Quaternary, or Isocratic Pumps without the Seal Wash Option installed.
Issue:
Worn pump seals can shed small particles that can cause blockages and pressure issues downstream of the...
This Information Applies To: Agilent G7167x Multisampler modules
Issue:
Required when:
The needle seat is visibly damaged, blocked, or is leaking.
Leaks or blockages in the Vialsampler are observed, especially between the needle and needle...
This Information Applies To: Agilent 1260 Isocratic (G1310B) Quaternary (G1311B) Pumps.
Issue
Required when:
The inlet valve is defective.
The pressure or leak test in Lab Advisor suggests the inlet valve may require replacement.
A large...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
Required when:
The outlet valve is defective or leaking.
The pressure or leak test in Lab Advisor suggests the outlet valve may require replacement...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
The seal wear in procedure is important as it acts to "bed-in" the seals to ensure a leak free and pressure-tight pump head.
Required when:...
This Information Applies To: Agilent G7167A/B Infinity II Multisamplers
Issue:
The Agilent Multisampler autoreferencing procedure uses predefined positions on the base plate and the sample hotel to calibrate the positioning of the needle parkstation...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Modules
Issue:
Reinstallation of the pump head on the pump metering drive during maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump...