A follow up question about this, if it ever occurs again. When the instrument errored out it prevented us from even initializing the instrument properly. Is it possible to auto reference even if the unit failed to initialize correctly?
Welcome everybody,
The problem occurred after updating Openlab CDS Software 2.2 Version to 2.4 Version.
GC# 7890B With FID , and TCD Detector
OpenLab CDS Software 2.4
After installing the software version 2.4 and after a gas sample injection…
Hello,
I have a question about our GC 8860, which has been experiencing some problems since I changed the valve pressure.
Although it works well immediately after the change, if I don't use the GC for a few days, the first few runs produce larger…
Hi All, I need help to fix either baseline drifted down or change volume injection of water samples in GC/FID. Specifically, I am setting up a new GC instrument for analysis of methanol and alcohols in water samples with the following conditions: - Instrument…
Hi Everyone,
Due to random readings of my samples, i ran wavelength and photometric accuracy test. Both of them fails, do i need to replace the lamp or is it because of the wavelength drive gear?
thanks.
The optional high vacuum gauge has a cable between the gauge and the electronics. It is either disconnected or the gauge has failed.
See page 125 and 126 in the 5977B Series MSD Operating Manual for instructions on how to turn it on and off.
The…
If you want to know what specific module is sending a Leak error, this article in the Knowledge Portal can help:
Determining which Module is Causing the Shutdown Error Due to a Leak
The "Valve command failed transport command failed" Error can have…
When the tuning is done at 3200 (+) everything is fine. When I change it to tune at 1700 (+) the masses are reasonably accurate. After it gets to the third mass (620) it appears that the entire spectrum shifts by about 1.5 AMU and the tuning fails. There…
There is an SP7 switching valve on our 5110 ICP-OES The first set of triplicate aspirations of Std always ride really close to the precision limit of 2%RSD and then std#2 and Std3 are typical 0.5 or less. (ISTD Method) All of these standards are in the…
I have a 7820A GC connected to a 5977B MS. When I submit a sample, it injects and runs as normal at first. Near the end of the run, an error message pops up that reads "Attempt to download method to GC failed." Additionally, when I check the logbook,…
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...