Hello, I would appreciate any help possible with this question. I have an Ultivo LC/TQ and it is having the problem with autotuning. It fails due to spray stability. Due to this I am thinking it might be the nebulizer? I take it out and see good spray;…
I have Software Leak Test Data Wizard for VS Series Leak Detectors, but have problem to reinstall because folder Data was corrupted the file data.cab missing. Failed to install. Can anyone help without need to buy new CD Software ? withou need to buy…
It's OK.
I don't know if the valve is included in the pump or somewhere else.
If the valve fails, we'll have to use our Agilent maintenance/repair contract to clean the system... ;)
Hello, Software: OpenLab Chemstation edition C.01.09 Software driver version: B.01.07.3[6648] Instrument: GC 7890B, Headspace 7697A I am using the above instrumentation and software. When I attempt to create a sequence/edit sequence table, I get the following…
My Agilent 5110v ICP-OES returns an error message "Timeout in plasma controller state operations (State 7)" or "ErrorNumber_PLASMA_CTRL_BASE_STATE_TIMEOUT" and the plasma fails to lit. Please, what how do I fix the error? I have cleaned the torch, and…
Hello,
Thank you for the response. I created MH_meida folder in C drive and also enabled .NET 3,5. But I received error message again after trying to install qual 10.0. Any suggestions would be much appreciated. Thank you.
here is the error log…
Is the MS still pumped down and ready to go? Do you have -- Use the MS -- checked in the method? If the column is connected to the FID and the MS is not running you'll need to uncheck that and save the method, hopefully with a new name like No_MS_FID_Only_28Feb2023…
Hello,
we are using a G1312B binary pump (1260 Infinity) and had the error message: Fan Failed
After acknowledging the error message I can turn on the module as usual and it is working quite fine.
Nonetheless, I am not sure whether the fan is working…
Hello, is it possible to operate a HP 5890 II with 7673 in standalone mode completely without computer/integrator?
I'm trying to set up a GC taken from a former GC-MS system working with a PC over GPIB. It should now work as GC-FID together with the…
This Information Applies To: Agilent GC Systems
Issue
Excessive baseline noise can be introduced at different points including sample preparation, sample introduction, separation, and the detector. The excessive background can cause reduced signal...
This Information Applies To: Agilent GC Systems
Issue
Baseline instability that is not reproducible across multiple runs can be introduced at different points including sample introduction, separation, and the detector. The baseline instability...
This Information Applies To: Agilent GC Systems
Issue
Peak fronting is present in a chromatography peak when it has an excessive asymmetry with a leading edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
This Information Applies To: Agilent GC Systems
Issue
A shift in retention time can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
A change in peak size can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
Peak splitting is when a single compound is shown in the chromatogram as two peaks usually unresolved, or one of the peaks is a shoulder.
Other chromatographic problems are identified in Basic...
This Information Applies To: Agilent GC Systems
Issue
This test isolates the point of contamination to the sample introduction system, which includes the gas supply, gas supply lines, and the sample inlet. It does not include the syringe or autosampler...
This Information Applies To: Agilent GC systems
Issue
Peak tailing is present in a chromatography peak when it has an excessive asymmetry with a trailing edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
T his Information Applies To: Agilent 8890/8860/7890/7820/6850/6890 GC Systems with TCD (Thermal Conductivity Detector)
Issue
Problems observed with thermal conductivity detector (TCD) results can have different underlying causes.
Resolution...
This Information Applies To: All GCs, 6890, 6850, 7890, 7820, 8890/8860, Intuvo 9000
Issue:
This article is a troubleshooting guide for when the Flame Ionization Detector (FID) does not ignite or the flame keeps going out.
Cause:
If the FID...