Canadian_Chemist ,
There is an example of printing text instead of the final concentration based on the LOQ outlier in this discussion.
(+) Report builder - Final Concentration Expression Change - Forum - Mass Spectrometry Software - Agilent Community…
When trying to close a connection on an instrument with an active single run or sequence the OpenLAB CDS software will usually give a message that it will close connection when the runs are finished. Today when trying to close 2 instruments on the same…
Yes, it is off on all gasses, always by roughly 20% (occasionally nearly 30% or as low as 15%, depending on the instrument). Air, Hydrogen, Makeup (N2), carrier (H2 or He) on every instrument (12 GC and 3 GC/MS, which haven't been evaluated). It's also…
Hi,
My baseline is around 8pA in standby state. H2 is coming from a tank and I can rule out contaminations in the gas source because the gas line is splitted with T piece: one is going to the FID EPC and one is going to the inlet PCM. H2 is the carrier…
Hello Agilent Users,
Im missing a feature in Openlab since day 1. How do I override and start a run if the GC is not ready ?
For example: the FID temperature is set at 250°C in the method and the actual temperature is at 220°C (it is still heating…
The GC counter rolls over at 999,999...but 100,542 is still a lot!
Great drawing, thanks. That setup makes it difficult to figure out pressures/flows. The path of least resistance is all of the 530 pieces unless the methanizer and the connection from…
The idea behind the multiple modes is to keep the flows going through your FID constant. Changing flows will change the flame characteristics and cause the baseline to shift. Some suggestions:
If your column is set to constant flow mode, use "Constant…
Hi all
Apparently the engineer who did the mainboard replacement made a mistake by plugging the MCGV cable to the SSV cable, this made the valve failed to switch (EE 2040.2) and electronic fuse of SSV (EE2049.0) error always appear. It was out of my…
We have a brand new Agilent 6495 LC/TQ system with a MS 120 rough pump. We vented and shut off the instrument for building maintenance over the weekend. On startup today, the rough pump receives power (the lights turn on) but eventually fails to engage…
This Information Applies To: Agilent GC Systems
Issue
Excessive baseline noise can be introduced at different points including sample preparation, sample introduction, separation, and the detector. The excessive background can cause reduced signal...
This Information Applies To: Agilent GC Systems
Issue
Baseline instability that is not reproducible across multiple runs can be introduced at different points including sample introduction, separation, and the detector. The baseline instability...
This Information Applies To: Agilent GC Systems
Issue
Peak fronting is present in a chromatography peak when it has an excessive asymmetry with a leading edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
This Information Applies To: Agilent GC Systems
Issue
A shift in retention time can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
A change in peak size can occur for single, multiple or all peaks.
Other chromatographic problems are identified in Basic Troubleshooting for GC Systems . Regular maintenance of your instrument...
This Information Applies To: Agilent GC Systems
Issue
Peak splitting is when a single compound is shown in the chromatogram as two peaks usually unresolved, or one of the peaks is a shoulder.
Other chromatographic problems are identified in Basic...
This Information Applies To: Agilent GC Systems
Issue
This test isolates the point of contamination to the sample introduction system, which includes the gas supply, gas supply lines, and the sample inlet. It does not include the syringe or autosampler...
This Information Applies To: Agilent GC systems
Issue
Peak tailing is present in a chromatography peak when it has an excessive asymmetry with a trailing edge. A normal peak is almost symmetrical.
Other chromatographic problems are identified...
T his Information Applies To: Agilent 8890/8860/7890/7820/6850/6890 GC Systems with TCD (Thermal Conductivity Detector)
Issue
Problems observed with thermal conductivity detector (TCD) results can have different underlying causes.
Resolution...
This Information Applies To: All GCs, 6890, 6850, 7890, 7820, 8890/8860, Intuvo 9000
Issue:
This article is a troubleshooting guide for when the Flame Ionization Detector (FID) does not ignite or the flame keeps going out.
Cause:
If the FID...