Hello I have an ICP-MS 7900. My Check Performace fails all the time. I washed the entire system and replaced the chambers and cone again. The same applies to oil changes. Nevertheless, my Check Performace fails. Can anyone help me with this? Or someone…
Hello
We have an agilent ultivo qqq and last week when trying to run a checktune it failed giving a message saying calibrant bottle is empty or nebulizer is clogged. Nevertheless the calibrant bottle is definitely not empty, and the nebulizer also doesnt…
Hello, I have a G1321B that showed errors during the OQPV. The FSE changed the flash lamp Iand the Intensity test is OK arround 10000 counts buen the and Raman ASTM Signal/Noise fail. I want to know if there are another test to do.
I changed my acquisition method from using front FID to back FID. I changed this in the acquisition method detector, signals, and columns sections. On my status tab, the detector is still showing front FID and the online signals is showing no options…
Hello,
Our lab currently uses a headspace-GC-FID to analyze for ethanol in blood samples. We have a multi-level, internal standard calibration curve as well as control samples at various concentrations that are analyzed in a sequence. Is there a way…
The Digest of upcoming webinars has been updated as of January 4.
Notable additions include:
Spectroscopy Digital Workshop & Bootcamp (16)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from contaminants…
Hello lperry ,
The document below explains what that error is, essentially it could be that an ALS is not ready for injection, or some other piece of hardware connected to the GC.
6890 GC Not Ready Messages (agilent.com) (bottom of page 9).
…
When doing autotune I get high precursor in mass 502. I get 12.79% and the limit is 12%. The manual says that it could be contaminated. The equipment has had preventive maintenance recently but it has now this problem. Previously it had a ratio of mass…
Hello,
I am expeirencing the same issue after having to reload E.02.02.1431. The quant report prints as one job and the chromatogram and the spectra reports (I'm printing a detailed report) print as a second job.
I've done as ron_tackett mentioned…
Hello vanphu, Thanks for the model information. On power on, the motor needs to move the pump to specified positions and if it fails to do so in a range of motor steps, it can give the error you mentioned. We advise to leave the pump stroke in auto to…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...